Find a Driveway Installer you can trust in Sandy.

Removing oil from block paving can be tricky, and a professional clean and re-point is often the best option. However, for small stains, especially recent ones, it’s worth attempting to clean it yourself. To do this, you can purchase oil remover or driveway cleaning solutions – although be careful, as some may stain or mark certain kinds of paving stones. In general, stay away from acid based cleaners.

• Where you live
• How big you want your driveway to be
• What colour or design you would like
• Whether any additional work will need to be completed to prepare the area for the driveway

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

Have you decided to install block paving and wondering what the best sand to be applied to the joints is in order to achieve a perfect job? Well, you’re at the right place! This is one of the most frequently asked questions when it comes to block paving and we seek to give you a reliable solution once and for all.

The best sand for block paving is a kiln-dried sand. It’s an extremely fine sand which has been dried in a kiln to get rid of all the water before it’s incorporated to achieve the best results. Therefore, the sand contains no moisture and is commonly used to fill the joints of block paving to keep the paving’s structure rigid and strong. It also goes a long way to prevent the ingress of water while stopping the paving from moving and becoming loose. The major reason why the paving sand must be dried is to allow it flow easily into the joints as well as the block paving’s gaps. As result of this smooth flowing to the bottom of the joints, there will be no sand sticking to the sides of the pavers.

Another major reason why kiln-dried sand is commonly applied to the block paving’s joints is to prevent water from penetrating the paved area. It also tightens the individual pavers together to prevent from moving and becoming loose. In the event whereby you happen to leave the joints of your block paving without kiln dried sand, it’s highly likely that they’ll sink as a result of water penetration and the blocks will become very loose. After washing block paving, it’s very important to also replace any sand washed off in the process once the paving is dried to prevent water ingress into the joints.

If you want your tarmac driveway or outdoor area to last as long as possible, it’s important to look after it. This means giving it a good clean every so often.

If there are any greasy or oily stains on your tarmac, you won’t get these off only using water. Get a degreaser and follow the instructions. You’ll then need to use a pressure washer or hose to rinse off the detergent and clean the rest of your tarmac or asphalt area.

Avoid getting your pressure washer too close to your outdoor surface or pointing it directly at it. You should also avoid cleaning the same area for too long. This will help you clean your tarmac while avoiding damaging it.

Paving can be used for driveways and is capable of bearing the weight of cars and other vehicles. Ensure that you choose the appropriate type of paving, as some are designed for paths or decorative use. Correct installation is vital as improperly installed paving may move or break under the weight of a car.

1. Prepare the base If you want your resin bound driveway to last a long time, you need to ensure that you prepare the base properly. Remove any block paving, grass or soil and dig down until you hit solid ground. Lay a sub-base of asphalt for good permeability. If you’re laying over the top of your current driveway, make sure that all cracks are increased into a ‘v’ shape with a saw and ensure the surface is dry and weed-free.
2. Mix the resin You must follow the instructions on the materials you have to the letter if you want the curing process to work. Usually batches come in ‘Part A’ and ‘Part B’. Keep the resin container secure and on a protective surface to avoid splashing, then mix Part A for 10-20 seconds at a slow speed with a helical bladed mixer. Add Part B and mix thoroughly at a slow speed for about 2 minutes until it’s blended together.
3. Mix the dried aggregates and sand with the resin Place a quarter of the aggregates into a mixer, then add the pre-mixed resin and start a stopwatch. You should then add the rest of the aggregates before slowly adding the sand. When you’re happy with that mix, stop the stopwatch. That time is the time that you need to spend mixing any other resin and aggregates to avoid colour variation.
4. Lay the mix on the surface Transfer the mix to the work area then plan a laying route. When the mix is laid out, use a very clean trowel to spread the mix. Clean it regularly during the process to avoid dragging aggregates out of place. Once the aggregates stop moving in a fluid movement and become solid, stop trowelling. Then you can polish the surface to give it an attractive shine.

From gravel and crushed stones to asphalt and tarmac, the choice when it comes to surfacing options for driveways is truly staggering. However, what’s not too clear is the options that best suits a sloping driveway. If you also possess a sloping driveway and wondering the best material to install, you’re definitely not alone. This is a major source of concern for several home and property owners in the UK being fully aware that making the wrong choice here can prove really costly and disastrous. In order to help you make the best informed decision possible, we’ve put together this post which takes a look at the various driveway material options available to you.

• Gravel
  This driveway surfacing option provides a truly enjoyable “crunch sound when driven on, however, the satisfaction will be short lived if installed on a sloped driveway. If installed on a sloped driveway, there’s going to be a continual displacement as instinctively rolls downhill on an incline.

• Concrete
  This can prove to be a great problem if installed on an incline. This is due to the fact that concrete is subject to freeze/thaw phenomenon which makes it steep and slippery lacking the needed traction.

• Tarmac
  This is particularly far from ideal when it comes to a steep driveway surface. This is because it requires continuous maintenance to prevent spillages from spoiling the surface.

• Resin
  The best surface for a steep driveway is simply that made from resin. This is due to the fact that this surfacing option allows water to soak away naturally. They’re perfectly permeable, preventing water from pooling and reducing the risk of falls.