Find a Renewable Energy Specialist you can trust in Kilmarnock.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.

It may be hard to believe with the summers we have in the UK, but there is more than enough sunlight to power solar panels. Solar PV (photovoltaic) panels operate in daylight, rather than needing direct rays from the sun so they’ll work throughout the year.

Whether installing an air source heat pump will help you save money depends on your property, how long you expect to live there, and the type of heat pump you get.

Air source heat pumps are initially quite expensive to install. However, if you get an air-to-water air source heat pump, you’re eligible for money from the Renewable Heat Incentive [https://www.energysavingtrust.org.uk/scotland/grants-loans/renewables/renewable-heat-incentive] (RHI). This is a UK government scheme that gives you quarterly cash payments over seven years if you install an eligible renewable heating technology (air-to-air air source heat pumps aren’t included).

All this means that if you have long-term plans to stay in your property, then an air-to-water air source heat pump can be a great way to save money on your heating bills. However, if you’re planning on moving out of your property relatively soon, or are a considering an air-to-air air source heat pump, it may not be the best financial option for you.

It’s important to remember that air source heat pumps are at their most efficient when installed in very well insulated properties. If your property’s not very energy efficient, you may find that a heat pump won’t help you save money.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Air source heat pumps work by taking heat from the air and using it to heat your home. They absorb heat from the air into a fluid, which then goes to a compressor where it gets hotter. This heat is then used to warm up water or air, which is distributed around your home.

First and foremost, you should know that heat pump is simply a device whose primary function is the transmission of thermal energy from one spot to the other. A good example can be found in the refrigerators whereby the evaporation as well as cooling of a liquid is incorporated to lower the storage compartment’s temperature. In recent times, this whole technology is utilized to draw the potential thermal energy present in the air outside and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. This is exactly what an air source heat pump does as it absorbs heat from the air and convert it into a higher temperature using a compressor. How the air source heat pump works is really simple, it’s just like a refrigerator but in reverse. Let’s take a look!

• The air source heat pump extracts heat present in the outside air into a liquid refrigerant at a reduced temperature.
• The pump then compresses the liquid to increase its temperature with the help of electricity. Once done, it then compresses it back to liquid so as to free the heat stored.
• The heat released is then directed to the radiators or under floor heating, while the ones left would be stored in the hot water cylinder.
• The hot water that’s stored can be used for showers, baths as well as taps.

Overall, the air source heat pump is an efficient way to make your home warm. It makes use of electricity to function, but it should consume lower electrical energy than the heat it generates.

How To Install Solar Panels And Batteries

Have you decide to purchase a solar system for your home and wondering how to go about the installation? If yes, then we’ve got you covered! In recent times, it’ll be totally safe to say that solar panels and batteries for home use in the UK has now become more of a necessity than a luxury considering the numerous benefits the system offers. However, with the cost of having the system installed, you might be forced to think about the doing the installation yourself.

If you lack proper training and experience in the solar system installation process, it’s advisable to hire the services of a qualified technician who can guarantee the best results the first time and help you save time and extra costs that may result from possible costly errors. Here, we’ll give you a good insight into the installation process.

• Mount the solar panel and ensure it’s properly screwed to your roof. Try to position in such a way that it faces direct sun rays to have enough solar power generated.

• Connect your charge controller. The current that’s being generated by the solar panels will not be stable all day long. As a result, it’s important to avoid connecting solar photo voltaic modules directly to your better, if you don’t want it damaged. To control the current received from the solar panels, the charge controller is required. It has three connecting points - one for the battery, one for the solar panels and the last for Direct Current (DC) identify the one for solar panels and connect accordingly.

• Connect the battery to charge controller. The charge controller possess two terminals for the battery - the positive and negative terminals. Connect the positive terminal to the positive of the battery and also do the same for the negative.

Not only will you reduce your electricity bill by generating your own electricity with solar panels, but you can also earn money through the SEG which is offered by large energy suppliers. They’ll pay you for the electricity you export back to the grid. You’ll also reduce your carbon footprint, lessening your impact on the environment.

• The power of your solar panel system – there's no point buying a higher capacity battery if your system will never generate enough electricity to charge it
• How often you think you will need to charge your battery
• Your budget
• Whether you care about having the latest technology and a recognisable brand name