Find a Renewable Energy Specialist you can trust in Maybole.

Air source heat pumps work by absorbing heat from the outside air and transferring it inside to heat up your property.

An air source heat pump has an outdoor unit containing a refrigerant. This absorbs heat from the air and passes into a compressor, where the temperature is increased. The heat then transfers either into water, which feeds into your wet heating system, or into air, which is dispersed around your property.

Air source heat pumps need electricity to run, but this is to power the compressor rather than directly generate heat.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

There are two main types of air source heat pump: air-to-water and air-to-air. They work in different ways and have different advantages and disadvantages. Make sure you do your research so you know which one is best for you. Alternatively a registered installer will be able to determine the best type for your property.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

If you’re thinking of adding a solar battery to your home, you might be wondering whether or not it’s going to work in a power cut. If yes, then you’re not alone as this is one of the most common questions asked when it comes to solar batteries. In this post, we aim to provide you with a detailed answer to solve this concern once and for all.

The answer to this question is, it depends. The main reason why your solar batteries will usually not work or provide your home with the much-needed back up power is as a result of the several threats it poses. You should be aware that both your solar panels and battery are connected to the main grid. When a power cut occurs, your engineers will have to operate on the grid. If the solar panels or batteries are in operation at the period there’s a high chance the engineers would be electrocuted by the electricity that’s being produced. As a result of this, solar inverters are usually designed to automatically switch off once a power cut occurs. However, it should also be noted that if your solar battery possesses backup functionality, you’ll be able to make use of your solar energy in the event of a power cut. In other words, what determines if your home battery would work in a power cut is the availability or otherwise of a backup functionality.

Furthermore, you might also wish to know if your solar panels will continue to charge the battery in a power cut. Well, this depends on the type of backup system you possess. There are some more affordable batteries that are designed to automatically release their stored energy upon the detection of a power cut. And this is mostly because the battery inverter is usually smaller than the solar inverter which allows the energy from the solar inverter to the transmitted to the battery - risking an overload. However, if otherwise, then energy can continue to be transmitted to the battery until its fully charged.

How Many Solar Panels And Batteries Do I Need?

Are you presently considering adding a solar system to your home? With several homeowners in the UK using solar now, many more are realizing the numerous benefits they stand to derive by getting one. Therefore, if you’re thinking about adding the system to your home but do not know where to start, you’ve come to the right place.

Here, we’ll help you calculate the number of solar panels and batteries you’ll need to power your home. Starting from the panels, you can begin by taken into account everything that makes use of power in your home to get a good idea of how many you’ll need.

• Firstly, you’ll have to determine the number of watts you use. Simply go through your utility bill for kilowatt-hours (kWh). This varies amongst homes and being able to identify your daily average energy usage will assist you in getting your solar needs.

• Secondly, you have to determine the peak sunlight hours - having in mind that the solar panels only work when under direct sunlight. Once determined, you can then multiply the figure in hours by your home’s hourly energy usage and divide by your selected solar panel’s wattage.

Generally for a 1500 square foot house, you might need around 15 to 18 solar panels to cover the house’s electricity.

Meanwhile for batteries, there are also some factors to be considered to determine the number of batteries you’ll need for your house. These factors include your home’s power or electricity usage, the period of time in which the battery will be used as well as the battery’ specifications. Once done, you’ll be able to calculate the number of batteries required by your home.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Air source heat pumps work by taking heat from the air and using it to heat your home. They absorb heat from the air into a fluid, which then goes to a compressor where it gets hotter. This heat is then used to warm up water or air, which is distributed around your home.

First and foremost, you should know that heat pump is simply a device whose primary function is the transmission of thermal energy from one spot to the other. A good example can be found in the refrigerators whereby the evaporation as well as cooling of a liquid is incorporated to lower the storage compartment’s temperature. In recent times, this whole technology is utilized to draw the potential thermal energy present in the air outside and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. This is exactly what an air source heat pump does as it absorbs heat from the air and convert it into a higher temperature using a compressor. How the air source heat pump works is really simple, it’s just like a refrigerator but in reverse. Let’s take a look!

• The air source heat pump extracts heat present in the outside air into a liquid refrigerant at a reduced temperature.
• The pump then compresses the liquid to increase its temperature with the help of electricity. Once done, it then compresses it back to liquid so as to free the heat stored.
• The heat released is then directed to the radiators or under floor heating, while the ones left would be stored in the hot water cylinder.
• The hot water that’s stored can be used for showers, baths as well as taps.

Overall, the air source heat pump is an efficient way to make your home warm. It makes use of electricity to function, but it should consume lower electrical energy than the heat it generates.