Find a Renewable Energy Specialist you can trust in Bracknell.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.

You shouldn’t need to maintain your solar panels much at all as long as there’s nothing piled up on top of the panels that could block out the sun. They are installed at an angle, so when it rains the water runs off them and gives them a clean. However, if this doesn’t quite cut it, you can spray them with a hose a few times a year.

Are you thinking about installing a solar thermal system in your home? If yes, the you’d most likely be wondering the exact amount the system is going to cost. Well, you’re not alone. This is one of the most common question when it comes to solar thermal systems and we aim to answer that in this article. So let’s get started!

Unfortunately, the cost of a solar thermal system can’t be given in a single, accurate answer as they vary widely. However, when getting a new solar thermal system, you can expect to pay a sum within the range of £3000 to £6000 ( this includes a lowered VAT rate of 5 percent). The figures provided takes into account the installation costs as well as all the parts ( such as control panel, solar collectors, hot water tank and pipes).

To determine the price of your system, the quality and type of the panels matter. For instance, according to the Solar Trade Association, a properly insulated twin coil cylinder system would be priced at around £4500. in the same tone, it’s also possible to get DIY solar thermal kits that includes all the required hardware which will cost within the range of £1500 to £250. This however, may not be eligible for government support. In order to benefit from the RHI, your system must be fitted by a MCS accredited installer.

The varying prices of the solar thermal system’s initial cost is based on the specification of each individual house. For example, in situations where the building is having complicated water system, the plumbing cost is expected to increase which will have a serious impact on the overall cost of the solar thermal power system.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Air source heat pumps work by taking heat from the air and using it to heat your home. They absorb heat from the air into a fluid, which then goes to a compressor where it gets hotter. This heat is then used to warm up water or air, which is distributed around your home.

First and foremost, you should know that heat pump is simply a device whose primary function is the transmission of thermal energy from one spot to the other. A good example can be found in the refrigerators whereby the evaporation as well as cooling of a liquid is incorporated to lower the storage compartment’s temperature. In recent times, this whole technology is utilized to draw the potential thermal energy present in the air outside and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. This is exactly what an air source heat pump does as it absorbs heat from the air and convert it into a higher temperature using a compressor. How the air source heat pump works is really simple, it’s just like a refrigerator but in reverse. Let’s take a look!

• The air source heat pump extracts heat present in the outside air into a liquid refrigerant at a reduced temperature.
• The pump then compresses the liquid to increase its temperature with the help of electricity. Once done, it then compresses it back to liquid so as to free the heat stored.
• The heat released is then directed to the radiators or under floor heating, while the ones left would be stored in the hot water cylinder.
• The hot water that’s stored can be used for showers, baths as well as taps.

Overall, the air source heat pump is an efficient way to make your home warm. It makes use of electricity to function, but it should consume lower electrical energy than the heat it generates.