Find a Renewable Energy Specialist you can trust in Glogue.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Are you thinking of installing solar thermal systems in your home or property and wondering exactly how it works to generate electricity? Regardless of your motive, in this article you’ll learn in simple details how solar thermal is how solar thermal doesn't provide electricity for your home.

If you are looking to generate electricity for your home then Solar PV are able to generate electricity simply by absorbing and focusing sunlight in such a way to create a temperature level that’s high enough to generate the much needed electricity. There are two main components that comes with the solar energy collectors of each. These two components include, the reflectors ( mirrors), which works to absorb and concentrate the sunlight onto a receiver. In several types of the solar thermal power systems, a heat transfer fluid is then heated and distributed in the receiver so as to generate steam. Once the steam as been produced, it’s then transported to the turbine where it’s turned into a mechanical energy, which in turn powers the generator to produce electricity.

Solar thermal power or electric systems are usually embedded with a tracking system which keeps the sunlight concentrated on the receiver all day long as the sun changes position in the sky. They also come with a wide array of collectors which works of distribute the heat absorbed to a turbine as well as the generator. A lot of solar thermal power facilities will gave two or more plants with different arrays and generators.

Solar thermal power systems can also have a thermal energy storage system component whose work is to permit the solar collector system to heat an energy storage system during the day while energy storage system’s generated heat is incorporated in the production of electricity at night or during a cloudy weather when there’s not much sunlight.

When people think about heat pumps, they’ll automatically have the believe that a swimming pool will require a big heat pump. Since the swimming pool has a large volume of water, then warming such a volume will require a large ground source heat pump because that volume is much larger than the normal domestic hot water tank, right? Well, that point of reasoning does seem logical especially with the information almost everywhere that ground source heat pumps are usually less efficient when it comes to heating hot water for home’s use. However, the fact is there are also some things to put into consideration that also works in favour of the ground source heat pump.

First and foremost, you should know your domestic hot water will typically be heated to a much higher temperature when compared to your swimming pool. Since you wouldn’t be using the water to disinfect your bathroom or doing your dishes in your swimming pool, then the temperature can be much lower. In fact, it’s much more comfortable and enjoyable to heat to a typical “swimming pool temperature than having it at a hot bath temperature. If you’ve ever wandered into a really hot swimming pool, you wouldn’t need any introduction to the painful discomfort that comes next.

As a result of this low temperature, your “tiny heat pump can operate a in a more efficient way which makes the use of ground source heat pumps a viable swimming pool heating option. What’s more? The ground source heat pump works for a swimming pool just like any any other application - moving the heat from the region of a warmer temperature to the cooler temperature region.

Air source heat pumps do make a bit of noise. However, it’s the external unit that makes the noise, minimising disruption in your home. And while it’s a good idea to ensure your external unit isn’t located directly under your bedroom window or very close to a neighbour’s property, it won’t be louder than 40-60 decibels. In many cases, this is actually quieter than a fossil fuel-powered boiler.

• The power of your solar panel system – there's no point buying a higher capacity battery if your system will never generate enough electricity to charge it
• How often you think you will need to charge your battery
• Your budget
• Whether you care about having the latest technology and a recognisable brand name

If you’re interested in getting a new air source heat pump, then you’d probably want to know if they’re really advantageous, cost effective and efficient. The fact is, there are a plethora of benefits that comes with using heat pumps which is a renewable alternative to warm up your home in the UK.

An air source heat pump can help you save money on energy bills while also minimizing your carbon footprint as compared to a gas or electric heating system. Another important benefit that comes with air source heat pump is the fact that they’re quire versatile and yet affordable. Generally, they can function either for heating or cooling purposes and they can also be incorporated for either heating of space or water. In fact, in order to achieve the target Net Zero by 2050, the UK government are looking to fit 19 million heat pumps in new builds. With significant rise in the deployment of heat pumps, the grants by the UK government enables this renewable energy source to become a lot more affordable to run while also helping to minimize the burden of the air source heat pump cost.

As perfect as it seems, this renewable source of energy also comes with a number of disadvantage which we’re going to list out. Let’s take a look!

• There must be sufficient space in your garden to accommodate the external condenser unit.
• The condenser unit can make a lot of noise and even blow colder air into their immediate area.
• Since they consume electricity to operate, this also means they’re not zero carbon unless the electricity is produced from a renewable source like solar panels etc.

Air source heat pumps work by absorbing heat from the outside air and transferring it inside to heat up your property.

An air source heat pump has an outdoor unit containing a refrigerant. This absorbs heat from the air and passes into a compressor, where the temperature is increased. The heat then transfers either into water, which feeds into your wet heating system, or into air, which is dispersed around your property.

Air source heat pumps need electricity to run, but this is to power the compressor rather than directly generate heat.