Find a Renewable Energy Specialist you can trust in Pencader.

Air source heat pumps can be a really efficient way to generate heat. Although they require electricity to run, they generate much more heat than an electric heater that uses the same amount.

Air source heat pumps provide heat at a lower temperature than most other types of space heating. This means they’re most efficient when they’re left on for longer periods of time, and distribute heat through wet heating systems with large surface areas, like underfloor heating or big radiators.

Air source heat pumps can be much more efficient than oil and LPG boilers, and older electric heating systems. However, they’re only usually the most efficient option if your property is very well insulated.

If you’re looking to purchase and install a solar system for your home or property, then knowing the amount of energy a solar panel can produce can go a long way to help you determine just how much solar panels that’ll be needed to power your entire house. In this article, we’ll give you an idea of the amount of energy that can be generated by a solar panel to help you make informed decisions going ahead.

First and foremost, you should note that each and every solar panel is rated by how much direct current power they’re able to generate under standard testing conditions. The output of a solar panel is given in watts units (W) and it stands for the theoretical power generation of the panel under direct sunlight as well as temperature conditions. Generally, several domestic solar panels possesses power output ratings which ranges from 250 watts to 400 watts. And as you would have expected, the higher power ratings are preferable when compared to the lower power ratings. What’s more? The total wattage of your solar panels will greatly influence a major part of your overall solar system cost.

Assuming you’re able to get just about 5 hours of direct sunlight every day, you can determine the output of your solar panel in this way - 5 hours x 290 watts ( wattage example of a premium solar panel) = 1450 watts-hours or approximately 1.5 kilowatts per hour (kWh). hence, the individual solar panel output in your array should be able to generate about 500 to 550 kWh of energy every year. This is sufficient energy to power some small appliances without problems.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

If you’re interested in getting a new air source heat pump, then you’d probably want to know if they’re really advantageous, cost effective and efficient. The fact is, there are a plethora of benefits that comes with using heat pumps which is a renewable alternative to warm up your home in the UK.

An air source heat pump can help you save money on energy bills while also minimizing your carbon footprint as compared to a gas or electric heating system. Another important benefit that comes with air source heat pump is the fact that they’re quire versatile and yet affordable. Generally, they can function either for heating or cooling purposes and they can also be incorporated for either heating of space or water. In fact, in order to achieve the target Net Zero by 2050, the UK government are looking to fit 19 million heat pumps in new builds. With significant rise in the deployment of heat pumps, the grants by the UK government enables this renewable energy source to become a lot more affordable to run while also helping to minimize the burden of the air source heat pump cost.

As perfect as it seems, this renewable source of energy also comes with a number of disadvantage which we’re going to list out. Let’s take a look!

• There must be sufficient space in your garden to accommodate the external condenser unit.
• The condenser unit can make a lot of noise and even blow colder air into their immediate area.
• Since they consume electricity to operate, this also means they’re not zero carbon unless the electricity is produced from a renewable source like solar panels etc.

The more you’re at home during the day, the more you can save on your electricity bill, since solar panels generate electricity during the day. The Feed-in Tariff scheme (FITs) ended in March 2019, but the new Smart Export Guarantee (SEG) pays you, via your energy supplier, for the electricity you export back to the grid. With the savings involved in generating your own electricity and SEG payments, you can expect to save up to £390 per year on your electricity bill.

Whether installing an air source heat pump will help you save money depends on your property, how long you expect to live there, and the type of heat pump you get.

Air source heat pumps are initially quite expensive to install. However, if you get an air-to-water air source heat pump, you’re eligible for money from the Renewable Heat Incentive [https://www.energysavingtrust.org.uk/scotland/grants-loans/renewables/renewable-heat-incentive] (RHI). This is a UK government scheme that gives you quarterly cash payments over seven years if you install an eligible renewable heating technology (air-to-air air source heat pumps aren’t included).

All this means that if you have long-term plans to stay in your property, then an air-to-water air source heat pump can be a great way to save money on your heating bills. However, if you’re planning on moving out of your property relatively soon, or are a considering an air-to-air air source heat pump, it may not be the best financial option for you.

It’s important to remember that air source heat pumps are at their most efficient when installed in very well insulated properties. If your property’s not very energy efficient, you may find that a heat pump won’t help you save money.