Find a Renewable Energy Specialist you can trust in Haddington.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

You shouldn’t need to maintain your solar panels much at all as long as there’s nothing piled up on top of the panels that could block out the sun. They are installed at an angle, so when it rains the water runs off them and gives them a clean. However, if this doesn’t quite cut it, you can spray them with a hose a few times a year.

The bigger the ground source heat pump, the better right? Wrong! And you’ll definitely be sorry to make such a huge mistake. When planning to install a heat pump, determining the size of the ground source heat pump is not as direct and straightforward as many homeowners would think. Here, you’ve got only a small margin for error. When the pump is too small, the heat pump will make use of the backup heater too often and in the event whereby the heat pump is too big, it’s going to short cycle. Both situations are preferably avoided as they’ll both leave you with an expensive and inefficient system.

To get the accurate size of a heat pump, there’s usually the need to hire the services of an expert and licensed heat pump installer who possesses a top notch design calculation software. In reality, the majority of inefficient systems are caused by a lack or poor understanding of the suitable design software.

There are many factors that can influence the calculation of a home’s heat pumps size. These includes

✓ Radiators and underfloor heating sizes

✓ Insulation, property fabric as well as heat loss

✓ The number of rooms in the property

✓ The types of rooms and their uses.

✓ The desired indoor temperature for varying rooms

✓ Seasonal temperature fluctuations.

Generally, a bigger house will require a bigger ground source heat pump. With an eye on the age of the property, heat loss as well as the types of the rooms, a house of about 100 square metre can require up to 4kW ground source heat pump. And for a house that’s about 200 square metre, the ground source heat pump also doubles to 8kW.

How To Install Solar Panels And Batteries

Have you decide to purchase a solar system for your home and wondering how to go about the installation? If yes, then we’ve got you covered! In recent times, it’ll be totally safe to say that solar panels and batteries for home use in the UK has now become more of a necessity than a luxury considering the numerous benefits the system offers. However, with the cost of having the system installed, you might be forced to think about the doing the installation yourself.

If you lack proper training and experience in the solar system installation process, it’s advisable to hire the services of a qualified technician who can guarantee the best results the first time and help you save time and extra costs that may result from possible costly errors. Here, we’ll give you a good insight into the installation process.

• Mount the solar panel and ensure it’s properly screwed to your roof. Try to position in such a way that it faces direct sun rays to have enough solar power generated.

• Connect your charge controller. The current that’s being generated by the solar panels will not be stable all day long. As a result, it’s important to avoid connecting solar photo voltaic modules directly to your better, if you don’t want it damaged. To control the current received from the solar panels, the charge controller is required. It has three connecting points - one for the battery, one for the solar panels and the last for Direct Current (DC) identify the one for solar panels and connect accordingly.

• Connect the battery to charge controller. The charge controller possess two terminals for the battery - the positive and negative terminals. Connect the positive terminal to the positive of the battery and also do the same for the negative.

Obviously the performance of a solar thermal system will vary depending on the location of the home, the insulation of the property, and your own hot water requirements. Solar thermal panels are capable of providing all of your hot water requirements from April to September. They will still make a contribution to your hot water needs for the rest of the year, but in general you will need a backup system to further heat the water in the colder months.

Biomass boilers can be designed to work with other kinds of heating. The most common of these is solar thermal. This is a popular renewable energy pairing. Solar thermal heating will meet your hot water needs during the summer while a biomass boiler can operate as a backup during the winter when solar thermal panels do not perform as well.

Air source heat pumps are a type of heating system that you can use to warm the air in your property. They’re a semi-renewable energy generator as, although they use electricity, they extract and use renewable heat from the air.

There are two main types of air source heat pump – air-to-water, and air-to-air. Air-to-water heat pumps are the most popular, and are best used to heat water that supplies underfloor heating systems or large radiators. Air-to-air pumps heat air, which is then dispersed round your property using fans.

Do you want a low carbon way of heating your home? Then, getting an air source heat pump is the way to go! What they do is pretty simple - they absorb the potential thermal energy present in the outside air and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. In other words, it functions by extracting heat from a cooler place and then uses it to raise the temperature inside a home or property. Being very similar to air conditioning units, the amount of heat they’re going to produce for your home or property will be dependent on the size you install. Therefore, the bigger the heat pump, the more the heat that’ll be generated.

Air source heat pumps have two main types which includes air to air and air to water. Air-to-water heat pumps works by absorbing heat from the outside air, then relays it directly into your home or property through the help of fans. In order to move the heat around your home, you’ll need a warm air circulation system. This type of air source heat pump are not eligible for the government’s Renewable Heat Incentive Payment as they can’t generate hot water. What’s more? They can function in reverse during the hot summer months.

Air-to-water heat pumps, on the other hand, operates by extracting heat from the outside air and transmitting it into the wet central heating system. Due to the fact that they’re able to generate heat that’s cooler than the one generated by a conventional gas or oil boiler, they happen to be a better fit for larger radiators or water underfloor heating.