Find a Renewable Energy Specialist you can trust in Longhope.

Air source heat pumps can be a really efficient way to generate heat. Although they require electricity to run, they generate much more heat than an electric heater that uses the same amount.

Air source heat pumps provide heat at a lower temperature than most other types of space heating. This means they’re most efficient when they’re left on for longer periods of time, and distribute heat through wet heating systems with large surface areas, like underfloor heating or big radiators.

Air source heat pumps can be much more efficient than oil and LPG boilers, and older electric heating systems. However, they’re only usually the most efficient option if your property is very well insulated.

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Are you currently considering installing a ground source heat pump in your home? Well, a heat pump can be a great alternative when compared to gas or oil boiler, however, you may also be worried about the operating efficiency of this heating system if you live in a cold climate or during the winter months. However, in reality, there’s nothing to be worried about!

A ground source heat pump works by incorporating the natural heat that’s typically found in the ground or groundwater. In other words, this type of heat pump doesn’t make use of fossil fuels to heat your home while it can also minimize carbon emissions that may pose a huge risk to the environment. This makes a popular option especially amongst home and property owners who are very environment conscious and prefers to utilize more renewable sources of energy.

However in a place such as the UK where the temperature can drop to around -10℃ during the winter months, it may get you thinking whether there’ll be enough heat in the ground to warm up your home. Let’s have a look.

In the UK, the temperature of the ground doesn’t normally fall less than 10℃. This is still enough heat for the ground source heat pump to warm up your home. In other words, as long as you purchase the right one, your ground source heat pump will continue to work just fine during the cold months. Due to the fact that every heat pump varies, you will need the right equipments so as to ensure the heat pump works well throughout the winter. This is usually not an issue in the UK, but same can not be said of colder places like Canada and North America.

No, air source heat pumps aren’t particularly noisy. Most models make about the same amount of noise as a boiler or fridge. And don't forget, the unit itself is fitted to the outside of your property so you won't hear a thing when you're indoors or at nightime!

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.