Find a Renewable Energy Specialist you can trust in Whitstable.

Air source heat pumps can be a really efficient way to generate heat. Although they require electricity to run, they generate much more heat than an electric heater that uses the same amount.

Air source heat pumps provide heat at a lower temperature than most other types of space heating. This means they’re most efficient when they’re left on for longer periods of time, and distribute heat through wet heating systems with large surface areas, like underfloor heating or big radiators.

Air source heat pumps can be much more efficient than oil and LPG boilers, and older electric heating systems. However, they’re only usually the most efficient option if your property is very well insulated.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

If you’re interested in getting a new air source heat pump, then you’d probably want to know if they’re really advantageous, cost effective and efficient. The fact is, there are a plethora of benefits that comes with using heat pumps which is a renewable alternative to warm up your home in the UK.

An air source heat pump can help you save money on energy bills while also minimizing your carbon footprint as compared to a gas or electric heating system. Another important benefit that comes with air source heat pump is the fact that they’re quire versatile and yet affordable. Generally, they can function either for heating or cooling purposes and they can also be incorporated for either heating of space or water. In fact, in order to achieve the target Net Zero by 2050, the UK government are looking to fit 19 million heat pumps in new builds. With significant rise in the deployment of heat pumps, the grants by the UK government enables this renewable energy source to become a lot more affordable to run while also helping to minimize the burden of the air source heat pump cost.

As perfect as it seems, this renewable source of energy also comes with a number of disadvantage which we’re going to list out. Let’s take a look!

• There must be sufficient space in your garden to accommodate the external condenser unit.
• The condenser unit can make a lot of noise and even blow colder air into their immediate area.
• Since they consume electricity to operate, this also means they’re not zero carbon unless the electricity is produced from a renewable source like solar panels etc.

If you happen to live in a quiet, serene environment ( or just cherish being in one) and wish to have an air source heat pump installed on your property, then you’d probably want to know just how noisy these renewable energy source are. In this post, we aim to provide answers to this question and more. Let’s take a look!

There is no short and direct answer to this question as air source heat pumps are available in varying shapes and sizes which makes the sound as well as volume of their noise different between models and manufacturers. However, as a result of government regulations, most of the contemporary air source heat pumps are able to function a lot quieter when compared to the older models. As you would have expected, modern air source heat pumps shouldn’t produce more than a low whirring sound provided they’re functioning as they should with no faults. On the other hand, the volume of the sound generated is largely dependent on the amount of work the air source heat pump is doing. This implies that a greater work load will generate a louder noise. This is due to the fan’s speed which works to absorb warm air into the compressor.

In order not to disturb the neighbours, noise pollution is normally determined at the design stage of the air source heat pump installation. The unit to be placed outdoor will typically be positioned as far from the neighbours property as possible and it’s also a great idea not to put the box directly under any windows. Overall, it’s always advisable to go for the newer models which tend to be better designed with thicker chassis and quieter fans.

Biomass boilers can be designed to work with other kinds of heating. The most common of these is solar thermal. This is a popular renewable energy pairing. Solar thermal heating will meet your hot water needs during the summer while a biomass boiler can operate as a backup during the winter when solar thermal panels do not perform as well.

If you’re thinking about getting a solar thermal system for your home, it’s normal to consider the possibility of using the system for central heating. So is this viable? In this article, you’ll learn how solar thermal panels can be incorporated for heating. Let’s have a closer look!

Heating and hot water systems, on the average, takes up a sizeable part ( up to 70 percent) of our energy bills. Now take a moment to imagine how cool it’ll be to generate your own hot water for free without having to depend on any supplier which in turn significantly reduces your energy bills. Well, this is exactly the work of central heating systems that are powered by solar. That’s super cool, right? Well, let’s have a look at how this works.

While solar panels generates electricity, solar thermal panels produces heat for hot water production. However, what’s important is the fact that they both make use of the sun’s natural energy to provide us with a free and renewable energy we can use in our homes. Here’s how it works.

Solar thermal panels directed at central heating incorporates the sun’s natural energy to heat water in a storage cylinder which is then available for use at home. These solar thermal panels are exposed to the sunlight by fitting them on the roof of the home. Generally, they’ll include tubes that contains liquid whose job is to collect the heat and then transfer it to a hot water cylinder that’s solar compatible in your home. The heat is generated for free and is also renewable. This is help you save lots of money on oil, gas and even electricity which you purchase to power the cylinder.

There are two main types of air source heat pump: air-to-water and air-to-air. They work in different ways and have different advantages and disadvantages. Make sure you do your research so you know which one is best for you. Alternatively a registered installer will be able to determine the best type for your property.