Find a Renewable Energy Specialist you can trust in Towcester.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

If you’re thinking about installing ground source heat pumps for your home, you’ll definitely want to know whether or not its worth the money. In this article, we’re going to look at the various benefits and drawbacks of the heat pump to enable you make an informed purchase decision.

As a result of their high efficiency rate and low running cost, ground source heat pumps are incredibly low carbon heating system which are presently experiencing a rapid increase in popularity, therefore they can actually be a valuable investment. This type of heat pump utilizes the constant temperature of the ground to provide warmth to your home - either for a space or for water heating purposes. Upon installation, the cost of running ground source heat pump is relatively low. What’s more? This type of heating system is eligible for the Renewable Heat Incentive (RHI) which means you can also earn an extra income on the side as well. However, what makes most homeowners think twice before installing a ground source heat pump is the high cost of installation.

Heat pumps are greatly essential especially when it comes to minimizing the UK’s total carbon emissions. At present, there about 240,000 units of the heat pump installed and to help attain the UK’s 2050 Net Zero goals, an extra 19 million heat pumps will have to be installed. If you wish to help in the achievement of this goal, you can start by investing in a ground source heat pump. So let’s look at some of the pros and cons of the heat pump.

PROS

✓ Low running costs

✓ Low carbon heating

✓ Energy efficient

✓ Eligible for grants

✓ Increases property value

✓ Provides both cooling and heating

✓ Inexhaustible

CONS

✓ High installation costs.

✓ The soil type impact its level of efficiency.

✓ It can be hard to install in retrofits.

How Many Solar Panels And Batteries To Power A House?

Do you wish to know the number of solar panels and batteries sufficient for a house? Well, this is a frequently asked question in the solar world which would be very difficult to provide an accurate answer. This is basically down to the fact that all homes are unique with different sizes as well as amount of daily energy requirements. As a result, the number of solar panels and batteries needed would be unique to the house in question. However, we’ll consider the varying influencing factors that will go a long way to help calculate the number of panels and batteries needed to power a house.

First and foremost, let’s take a look at the solar panels. You’d have to start here by putting into consideration all household appliances that makes use of power in the house to get a good idea of how many that’ll be needed.

• How Many Watts Is Being Used In The House On A Daily Basis?

To determine this, simply go through your utility bill for kilowatt-hours (kWh). This varies amongst homes and being able to identify your daily average energy usage will assist you in getting your solar needs.

• What Is The Number Of The Peak Sunlight Hours At The House’s Location?

Having in mind that the solar panels only work when under direct sunlight, the first step to determine the peak sunlight hours. Once determined, you can then multiply the figure in hours by the house’s hourly energy usage and divide by the solar panel’s wattage.

Overall for a 1500 square foot house, the number of solar panels that’ll be required should fall around 15 to 18.

Meanwhile for batteries, there are also some factors to be considered to determine the number of batteries that is required to power a house. These factors include the house’s power or electricity usage, the period of time in which the battery will be used as well as the battery’ specifications.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

How To Install Solar Panels And Batteries

Have you decide to purchase a solar system for your home and wondering how to go about the installation? If yes, then we’ve got you covered! In recent times, it’ll be totally safe to say that solar panels and batteries for home use in the UK has now become more of a necessity than a luxury considering the numerous benefits the system offers. However, with the cost of having the system installed, you might be forced to think about the doing the installation yourself.

If you lack proper training and experience in the solar system installation process, it’s advisable to hire the services of a qualified technician who can guarantee the best results the first time and help you save time and extra costs that may result from possible costly errors. Here, we’ll give you a good insight into the installation process.

• Mount the solar panel and ensure it’s properly screwed to your roof. Try to position in such a way that it faces direct sun rays to have enough solar power generated.

• Connect your charge controller. The current that’s being generated by the solar panels will not be stable all day long. As a result, it’s important to avoid connecting solar photo voltaic modules directly to your better, if you don’t want it damaged. To control the current received from the solar panels, the charge controller is required. It has three connecting points - one for the battery, one for the solar panels and the last for Direct Current (DC) identify the one for solar panels and connect accordingly.

• Connect the battery to charge controller. The charge controller possess two terminals for the battery - the positive and negative terminals. Connect the positive terminal to the positive of the battery and also do the same for the negative.

Solar panels provide an alternative to paying expensive National Grid energy rates, so primarily their first major benefit is helping to reduce bills. Solar PV panels will produce free electricity, whilst solar thermal panels generate heat for hot water and space heating. There are also payment incentives known as the Feed-in Tariff scheme (FITs) (for solar PV) and the Renewable Heat Incentive (for solar thermal) which guarantee a tax-free income for 20 years.