Find a Renewable Energy Specialist you can trust in Llanwrtyd Wells.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

No, air source heat pumps aren’t particularly noisy. Most models make about the same amount of noise as a boiler or fridge. And don't forget, the unit itself is fitted to the outside of your property so you won't hear a thing when you're indoors or at nightime!

Whether solar panel batteries are worth it depends on how much you’re at home and how big your solar panel system is. If you’re at home most of the day and your solar panels only generate enough electricity for you to use while for that day, then a battery probably isn’t worth investing in. However, if you have a large system that generates more than you can use or you’re out most of the day, then solar panel batteries are definitely worth it.

A solar battery storage system works by storing the electricity that your solar panels generated until you need to use it. That’s why they’re great for people that are out all day – your solar panels generate electricity all day whilst the sun’s out, but no one’s home so you’re using minimal energy except for things like your fridge and any appliances on standby. Most of the electricity charges your solar panel battery. Then, when you get home, your battery will discharge, and you’ll use all the solar electricity that your panels generated during the day.

Solar batteries are also excellent for people with large solar panel systems that generate more than they use in the day. Any electricity that you don’t use during the day will charge the battery, so in the evening when the sun goes down, you’ll just use the excess electricity that’s stored in the battery.

To work out whether solar panel batteries are worth it for you, you’ll need to work out how much of your solar electricity you’re using already. If you’re at home and you’re able to run your appliances all while your solar panels are generating electricity, a battery might not be worth it. Also, if you’re receiving export payments from the Feed-in Tariff Scheme (FITs) or the Smart Export Guarantee (SEG), you might want to look at the rate you’re getting paid. If it’s a good rate, it might be more cost-effective to continue exporting unused electricity to the grid. Speak to an MCS-registered installer that will be able to help you work this out.

Solar cells , also referred to as photovoltaic cells (PV), absorbs energy from the sun and converts it to generate electricity. This, however, should not be confused with photovoltaic thermal cells or PVT which operates to generate heat for water in homes. Solar cells are linked electrically and also carefully organized into a large frame which is popularly called solar panels. Generally, solar cells are produced or made of silicon semi conductors which works to absorb sunlight and then turn it into electricity for use at a home. A solar panel comprises of either 60 or 72 solar cells which are electrically interconnected in series and parallel and also positioned in between glass and plastic which is then framed.

At present, solar panels incorporated for residential or domestic purposes only possesses the capacity to make use of only about 20 percent of the sunlight they’re able to absorb and convert it to electricity - also called solar efficiency. Available in the market are also a wide range of solar cell available for both industrial and commercial purposes. This type of solar panels have an efficiency rating of about 40 percent which will also automatically make them more costly than the domestic types.

One great thing about the solar industry is the fact that it keeps improving in such a way that raises both its efficiency as well as overall quality. And with further research and development, this is expected to even increase as the years go by. What’s more? As these aspects keep rising, it’s also expected that the solar panels price should be on a decrease. That way, they’ll become available to a wider range of individuals who’ll also like to save money on electricity bills and go greener.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.

Are you thinking about installing a solar thermal system in your home? If yes, the you’d most likely be wondering the exact amount the system is going to cost. Well, you’re not alone. This is one of the most common question when it comes to solar thermal systems and we aim to answer that in this article. So let’s get started!

Unfortunately, the cost of a solar thermal system can’t be given in a single, accurate answer as they vary widely. However, when getting a new solar thermal system, you can expect to pay a sum within the range of £3000 to £6000 ( this includes a lowered VAT rate of 5 percent). The figures provided takes into account the installation costs as well as all the parts ( such as control panel, solar collectors, hot water tank and pipes).

To determine the price of your system, the quality and type of the panels matter. For instance, according to the Solar Trade Association, a properly insulated twin coil cylinder system would be priced at around £4500. in the same tone, it’s also possible to get DIY solar thermal kits that includes all the required hardware which will cost within the range of £1500 to £250. This however, may not be eligible for government support. In order to benefit from the RHI, your system must be fitted by a MCS accredited installer.

The varying prices of the solar thermal system’s initial cost is based on the specification of each individual house. For example, in situations where the building is having complicated water system, the plumbing cost is expected to increase which will have a serious impact on the overall cost of the solar thermal power system.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.