Find a Renewable Energy Specialist you can trust in Rotherham.

If you happen to live in a quiet, serene environment ( or just cherish being in one) and wish to have an air source heat pump installed on your property, then you’d probably want to know just how noisy these renewable energy source are. In this post, we aim to provide answers to this question and more. Let’s take a look!

There is no short and direct answer to this question as air source heat pumps are available in varying shapes and sizes which makes the sound as well as volume of their noise different between models and manufacturers. However, as a result of government regulations, most of the contemporary air source heat pumps are able to function a lot quieter when compared to the older models. As you would have expected, modern air source heat pumps shouldn’t produce more than a low whirring sound provided they’re functioning as they should with no faults. On the other hand, the volume of the sound generated is largely dependent on the amount of work the air source heat pump is doing. This implies that a greater work load will generate a louder noise. This is due to the fan’s speed which works to absorb warm air into the compressor.

In order not to disturb the neighbours, noise pollution is normally determined at the design stage of the air source heat pump installation. The unit to be placed outdoor will typically be positioned as far from the neighbours property as possible and it’s also a great idea not to put the box directly under any windows. Overall, it’s always advisable to go for the newer models which tend to be better designed with thicker chassis and quieter fans.

You shouldn’t need to maintain your solar panels much at all as long as there’s nothing piled up on top of the panels that could block out the sun. They are installed at an angle, so when it rains the water runs off them and gives them a clean. However, if this doesn’t quite cut it, you can spray them with a hose a few times a year.

The bigger the ground source heat pump, the better right? Wrong! And you’ll definitely be sorry to make such a huge mistake. When planning to install a heat pump, determining the size of the ground source heat pump is not as direct and straightforward as many homeowners would think. Here, you’ve got only a small margin for error. When the pump is too small, the heat pump will make use of the backup heater too often and in the event whereby the heat pump is too big, it’s going to short cycle. Both situations are preferably avoided as they’ll both leave you with an expensive and inefficient system.

To get the accurate size of a heat pump, there’s usually the need to hire the services of an expert and licensed heat pump installer who possesses a top notch design calculation software. In reality, the majority of inefficient systems are caused by a lack or poor understanding of the suitable design software.

There are many factors that can influence the calculation of a home’s heat pumps size. These includes

✓ Radiators and underfloor heating sizes

✓ Insulation, property fabric as well as heat loss

✓ The number of rooms in the property

✓ The types of rooms and their uses.

✓ The desired indoor temperature for varying rooms

✓ Seasonal temperature fluctuations.

Generally, a bigger house will require a bigger ground source heat pump. With an eye on the age of the property, heat loss as well as the types of the rooms, a house of about 100 square metre can require up to 4kW ground source heat pump. And for a house that’s about 200 square metre, the ground source heat pump also doubles to 8kW.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

How Do Solar Panels And Batteries Work Together?

With solar panel system rapidly becoming an ubiquitous phenomenon within the modern society, several homeowners in the UK are just coming to terms with the numerous benefits offered by the system. The solar power’s popularity has even led to the rise of another renewable technology - solar batteries able to store excess solar power that can be used later. Now several companies such as Tesla are now building solar batteries that can be fitted alongside solar panels for your building. So how exactly do solar panels and batteries work together? Let’s have a look!

Solar panels make use of the sun light to generate electricity and as a result, they can’t function when sunlight is absent - giving a big issue of how to power your house when it’s dark. In the event whereby this occurs, you’re afforded two options which is either to contact energy providers to buy electricity or purchase a battery storage system.

So what’s the function of the battery storage system? Basically when your solar panel provides electricity which is not needed right away, a solar battery will work to convert the DC electricity into AC energy which is going to be stored for later use (when you actually need it). in other words, your solar panels charge the batteries when you do not require the energy they’re generating right away.

As a result, when it’s dark and the solar panels are no longer functioning, your system will tap into the energy that’s already been stored by your battery for later use. This way, you can be totally independent of the National Grid, which implies more savings on your electricity bills.

Air source heat pumps do make a bit of noise. However, it’s the external unit that makes the noise, minimising disruption in your home. And while it’s a good idea to ensure your external unit isn’t located directly under your bedroom window or very close to a neighbour’s property, it won’t be louder than 40-60 decibels. In many cases, this is actually quieter than a fossil fuel-powered boiler.