Find a Renewable Energy Specialist you can trust in Bilston.

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

Air source heat pumps do make a bit of noise. However, it’s the external unit that makes the noise, minimising disruption in your home. And while it’s a good idea to ensure your external unit isn’t located directly under your bedroom window or very close to a neighbour’s property, it won’t be louder than 40-60 decibels. In many cases, this is actually quieter than a fossil fuel-powered boiler.

The importance of selecting the right size battery for your home simply cannot be overemphasized. A lot of home and property owners are facing this challenge and understandably so. Selecting the right battery size for your needs depend on a number of factors which includes your motive for adding a battery, your electricity usage, your budget as well as your panel array size, be it new or existing. In this post, we’re going to take you through some of these factors to help you determine the right battery size for your home or property. Let’s take a look!

• Your motive for getting a battery. While most people purchase a battery to wipe out their need to purchase electricity from the grid with the hope of making some savings, others add a battery so as to enjoy backup power. There are also some who just needs it to power their home with solar energy. It’ll not be economical to size a battery to effectively take you off the grid, but if your motive is to make savings, then you’ll should expect to purchase some electricity from the grid during the year.
• Electricity usage. The average household uses about 16kWh of electricity on a daily basis. During the daylight hours, most of these household will use a third of their electricity when the solar panels are still generating electricity, while the remaining two third are purchased from the grid. In other words, you’ll require a minimum of 10kWh battery capacity if you were to use a battery to power the electricity you purchase from the grid.

For a typical British household, you’ll most likely need a 5kWh solar power system which normally generates about 17 to 21 kWh on a daily basis depending on your location in the UK.

If you look after your air source heat pump, it can last for over 20 years. Make sure you check it every year and get a registered or qualified installer to check it every 3-5 years to prolong its life. If in doubt, check the manufacturer’s maintenance instructions.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.