Find a Renewable Energy Specialist you can trust in Redditch.

Biomass boilers can be designed to work with other kinds of heating. The most common of these is solar thermal. This is a popular renewable energy pairing. Solar thermal heating will meet your hot water needs during the summer while a biomass boiler can operate as a backup during the winter when solar thermal panels do not perform as well.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

If you happen to live in a quiet, serene environment ( or just cherish being in one) and wish to have an air source heat pump installed on your property, then you’d probably want to know just how noisy these renewable energy source are. In this post, we aim to provide answers to this question and more. Let’s take a look!

There is no short and direct answer to this question as air source heat pumps are available in varying shapes and sizes which makes the sound as well as volume of their noise different between models and manufacturers. However, as a result of government regulations, most of the contemporary air source heat pumps are able to function a lot quieter when compared to the older models. As you would have expected, modern air source heat pumps shouldn’t produce more than a low whirring sound provided they’re functioning as they should with no faults. On the other hand, the volume of the sound generated is largely dependent on the amount of work the air source heat pump is doing. This implies that a greater work load will generate a louder noise. This is due to the fan’s speed which works to absorb warm air into the compressor.

In order not to disturb the neighbours, noise pollution is normally determined at the design stage of the air source heat pump installation. The unit to be placed outdoor will typically be positioned as far from the neighbours property as possible and it’s also a great idea not to put the box directly under any windows. Overall, it’s always advisable to go for the newer models which tend to be better designed with thicker chassis and quieter fans.

Are you interested in installing an air source heat pump in your home or property? If yes, then you’d probably want to know just how much this is going to cost. Well, so are many other potential investors in the unit and we aim to answer this question once and for all. In this post, you’re going to discover the price range at which your new air source heat pump will fall in.

As simple as it seems, the cost of an air source heat pump can’t be accurate and straightforward as there are a number of factors that greatly influences the price. These influencing factors include the size of the heat pump, the system’s complexity, your personal preference - whether simple or advanced controls, and lots more. However, according to Energy Saving Trust, an air-to-water heat pump should fall within the range of £7000 to about £11000. What’s more? You’ll also need to put into consideration the cost of upgrading your radiators or fitting underfloor heating which can also cost you thousands of pounds.

In general, the main cost of a heat pump is the upfront cost of making a purchase as well as installing it. The heat pump will consume a little amount of electricity and the running costs are also relatively low. The amount your air source heat pump will cost largely depends on your home’s size, the temperature you want your home or property to be as well as how properly insulated your home is.

The period of time it’ll take to recoup your investment in the system in energy savings will also depend on a wide range of factors including the price you pay for electricity, how efficiently the system works, how you use the heat generated and more.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

Not only will you reduce your electricity bill by generating your own electricity with solar panels, but you can also earn money through the SEG which is offered by large energy suppliers. They’ll pay you for the electricity you export back to the grid. You’ll also reduce your carbon footprint, lessening your impact on the environment.

The bigger the ground source heat pump, the better right? Wrong! And you’ll definitely be sorry to make such a huge mistake. When planning to install a heat pump, determining the size of the ground source heat pump is not as direct and straightforward as many homeowners would think. Here, you’ve got only a small margin for error. When the pump is too small, the heat pump will make use of the backup heater too often and in the event whereby the heat pump is too big, it’s going to short cycle. Both situations are preferably avoided as they’ll both leave you with an expensive and inefficient system.

To get the accurate size of a heat pump, there’s usually the need to hire the services of an expert and licensed heat pump installer who possesses a top notch design calculation software. In reality, the majority of inefficient systems are caused by a lack or poor understanding of the suitable design software.

There are many factors that can influence the calculation of a home’s heat pumps size. These includes

✓ Radiators and underfloor heating sizes

✓ Insulation, property fabric as well as heat loss

✓ The number of rooms in the property

✓ The types of rooms and their uses.

✓ The desired indoor temperature for varying rooms

✓ Seasonal temperature fluctuations.

Generally, a bigger house will require a bigger ground source heat pump. With an eye on the age of the property, heat loss as well as the types of the rooms, a house of about 100 square metre can require up to 4kW ground source heat pump. And for a house that’s about 200 square metre, the ground source heat pump also doubles to 8kW.