Find a Shop Fitter you can trust in Dromore.

Is your garage door a bit old and outdated? Are you planning to make some renovations? Or perhaps you just want a newer and more stylish garage door, that’s safer and easier to operate, installed. Fitting a garage door can be a bit tricky but it’s not as difficult as you might think. If you’re without proper training or experience, it’s advisable to get in touch with a reliable professional for help in order to guarantee the best results while also saving you both time and money. This guide offers you step by step instructions to assist you in the installation of a new door on our garage.

To get started, the obvious first step is to remove the old garage door. Carefully go through the manufacturer’s instructions to achieve this. Here, you’d basically have to unlatch the door, take apart the door’s panel and unscrew the tracks.

lMeasure, Fit The Hinges & Handles

• Take a measurement of the area in which the door will be fitted

• From the top of opening to ceiling should include a space of about 10 to 12.

• For the length of the garage, you should have the door’s height with about 18 or more space.

• Once done, attach stops to the sides of the opening

• Lay out the bottom piece of the door and include the weather stripping (if you deem fit) using the sawhorses.

lPut The Bottom Piece In Position

• Fit the bottom piece into door frame using a level

• Hit nails partway into each jamb

• Bend the nails slight to secure their position.

• Assemble the vertical, curved and horizontal pieces of the track using the manufacturer’s instruction

lFit The Remaining Panels

• Put the second panel on the first panel

• Use a hammer to hit nails into it

• Fit the hinges.

• Repeat the process for the number of panels required and achor individual piece into the door jamb.

lInstall Rollers

• Fit the rollers in the section’s supports

• Put the rollers in the assembled track and make sure they’re not pressed to tightly against the track to prevent friction.

lSecure Tracks & Fit The Springs

• Fit the curved and horizontal pieces

• Assemble the springs following the manufacturer’s instructions

• Ensure that the tracks are level and parallel by lifting the door to about half length

• Lift the door to cover the distance left and fit the springs to the pulley system

Also commonly referred to as brown rot, dry rot simply means a decay of the root as a result of fungi which may negatively impact the wooden structures in the interior or exterior of your home or property. When the dry rot happens, the fungi present breaks down the cellulose as well as hemicellulose – the components which are responsible for the strength and resilience of the wood. Consequently, the wood is left weakened and brittle while also appearing a bit blocky. Most often than not, dry rot affects damp timber, primarily with a moisture content that’s more than 20 percent. As a result of this, any dry rot eradication strategy should have the removal of the source of moisture to form the core of its activities. So, how can you identify dry rot? Let’s take a look!

• Examine the wood. At first, the fungus appears a lot similar to cotton wool and may also possess water droplets on its surface if there is a very humid surrounding.
• Look out for shrunken or sunken wood.
• Identify darkening and cracks in the structure of the wood.
• Identify affect wood that features flat skin-like grown that may appear like the exterior of a mushroom with shades of silver and grey. Most times, patterned with patches of light purple or yellow which easily peels.

Dry rot can be treated in a number of ways which includes epoxy treatments, commercial anti-freeze as well as copper compounds. The epoxy treatment simply means the act of filling in channels within the damaged wooden structure with an epoxy treatment to eliminate the rot and strengthen the structure of the wood. The commercial antifreeze is the treatment of the rot with antifreeze to kill the fungus and prevent further growth.

The roof is the place that your conservatory is most likely to get grubby, but cleaning it is easy. You shouldn’t need to use any powerful cleaners – just warm water and a mild detergent.

The best tool to use to access your conservatory roof is a telescopic brush. This will help you get into corners and high areas without needing to work from height. You can use a ladder to help you clean your conservatory roof, but you should be very careful to avoid leaning it against any glazing

.

Consider investing in a telescopic cleaner with squeegee, brush and mop attachments to help you achieve a great finish on your aluminium conservatory.

Two of the commonly used terms in the UK and Irish construction industry is “First Fix and “Second Fix First fix encompasses all the work required to take a building from foundation to stroking plaster on the interior walls. This comprises of building walls, floors and ceilings, and implanting cables for electrical supply and pipes for water supply.

Some claim that First Fix starts after the shell of the building is complete, and ends when the walls are plastered. Some of the elements in the first fix are as follows.

• Drain runs: must be downhill and straight

• Spare conduits: drawstrings

• Soil pipes

• Copper pipes

• Normal pipes

• Doorbell

• Door frames

• Pocket doorframes

• Stairwell

• MVHR (mechanical heat recovery ventilation runs)

• Push-fit or other plastic piping

• Electrical back boxes

• Electricity cable runs

• Telephone, data and audio-visual cables

• Socket location

• Security

• Fire alarm

• Sound insulation

• Plasterboarding

It is to be kept in mind that the list goes on as there are several things that you can do when you are building a house from scratch and it is impossible to cover each and every aspect in detail.

The second fix includes all the work after the plastering of a complete house. These include linking cables to the electrical fittings, coupling pipes to the baths and sinks and fitting doors into doorframes. Second fix work requires a tidier finish than the first fix.

Carpenters, electricians and plumbers get a proper idea on the division of work. They will also be able to visit the construction site at different times.

Project managers can simply report it as the "first fix complete" or "the second fix 50% done" and others would very easily understand.

Regardless of the fact that a construction company might specialise in a certain form of fix, be it the first or the second, they are obligated to have a rudimentary understanding of both and are required to perform them from time to time.

How Does Electric Central Heating Work?

An electric central heating works to provide a number of benefits for you. These benefits include the following:

lSpace Heating

• The storage heaters work during the night to store electricity which would be used to heat up the heat retaining bricks. This, in turn, will release this energy throughout the day to warm up the room.

• There are also electric radiators which works to deliver on-demand heat and as a result, economy tariffs are totally avoided. It will generate heat by itself rather than storing it and with the controls, you can easily determine the amount of heat to be released when you require it.

• There is the wet electric system options as well which comes with water filled radiators. This operates in a similar way to normal radiators, however, it makes use of electricity to heat up the water.

lWater Heating

• An electric boiler operates in a very similar manner to other boiler types, just that it makes use of electricity as its fuel. Here, the water is warmed by a heating element and the water is later moved to several radiator throughout the house by a pump. These electric boiler types earns you tariff savings as you’ll be able to heat water at night.

• Heat pumps geothermal or air source, redistributes heat instead of creating it. Heat pumps are powered by electricity and it works by absorbing heat either from the air or ground which it then channels it through a pump. This can then be incorporated in heating either water or a room.

• A dedicated immersion heater is another water heating option. Here, the heating element is positioned inside a hot water cylinder. In a similar fashion to a kettle, the element heats the nearby water. Immersion heater can act either as a backup or your main heating element.

Smart controls such as Hive are the next generation technology with more and more people now converting their houses into smart homes to control multiple devices in the homes remotely. Smart technology can be incorporated with several household devices such as security, lighting, entertainment and more. But what if there’s an oil boiler installed in your home, can you still connect your Hive with the your heating? Well, simply read on to find out.

The answer to this question is yes, most oil boilers are compatible with Hive and can substitute for either an existing conventional programmer or thermostat. The smart technology works to help derive more benefits from your heating system and they usually come with apps which can be used to control your home’s heating from anywhere with just your mobile device. Hive, however, cannot work to replace the functions of smart oil boiler heating controls to modulate your heating as they only work on an on or off basis. To make use of the modulating technology in an oil boiler, the cost of manufacture would be considerably higher while offering little advantage in efficiency for the home or property owner. Ultimately, this implies that you can’t incorporate smart technology to control the output in a similar way as a gas boiler, but there are still some ways to utilize smart technology with your oil boiler in such a way to boost your efficiency and lessen the energy bills.

Do you want to use your Hive with your home’s oil boiler? We’d advise you get in touch with an OFTEC qualified engineer if you wish to install Hive Active Heating on your oil boiler, as British Gas engineer do not offer this service.

Garden slabs are a joy to behold but only when done the right way. Well, the installation of paving slabs shouldn’t be exceed digging a little here and there, buying a small amount of mortar and pressing down the garden slab, right? Absolutely not! But we must admit how great it would have been if only it were that easy in real life. Let’s be honest, in reality, laying garden slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. Consequently, this happens to be a stressful and quite tricky challenge. If you lack the required confidence to pull this off, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the garden slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

1. Mix a layer of mortar for each paver.
2. Apply the mixed mortar onto the sub base by using the trowel.
3. Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.
4. Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.
5. Take a measurement of the gap between the pavers
6. Repeat the above steps until all pavers have been perfectly laid
7. Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.
8. Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard-bristled brush.

Does A Conservatory Add Value?

if you’re looking to get a new conservatory built in your home or you’re moving into a new home that features a conservatory, it’s understandable if you’re wondering whether or not a conservatory adds value to a property.

Adding a conservatory to your home will not only create additional space, but it’ll also add value to it. When the right style, fit and shape is chosen, your conservatory can become an asset that’ll be well worth the investment when you want to dispose your home or property. Generally, a conservatory is estimated to add about 7 percent value to a home as stated by a popular property personality Phil Spencer. However, the correct level of the value it adds will be based on how well your conservatory is built as well as well it matches with its surroundings. As a result, when building your conservatory, it’s crucial to make sure that the new living space fits your home perfectly well in such a way that it showcases your property’s style of interior in order to create continuity.

When building your new living space, the first thing to do is to determine the best place for the structure to be placed. This should be given your total consideration because conservatories that look out of place can actually end up causing more harm than good like reducing the value of your property, as the potential investor may see it as more of a burden pr something that needs to be fixed.

If you choose a conservatory that perfectly suits the rest of your home and also creates value by allowing you derive maximum benefits from your garden, it’s likely to be a hot cake amongst potential buyers.