Find a Shop Fitter you can trust in Penrith.

Yes, bricklayers can work during the cold months, but it all depends on the type of work involved. For instance, residential housing maintenance works such as tuck pointing deficient mortar joints on exterior walls and columns as well as rebuilding of chimneys are best tackled during summer or simply put, the warmer months of the year. This is is mainly because the best results for these activities are achieved in the warmer months and several bricklayers will agree to this fact.

Mixing of mortar using anti-freeze technique to counter-act the effects of a cold weather can lead to white marks trailing down the brick when warmer temperatures comes knocking. As a result, even mortar mixing should be done at temperatures exceeding zero degree farenheit which will hold no serious consequences if the temperature should change to a little bit below the norms. During the winter, a good technique that can be incorporated to when mixing mortar would be to mix them in smaller quantities in a warmer environment. These small quantities will immediately be fed by the labourers to the bricklayers and in such circumstances, the mixed mortars will not be subjected to a freezing temperature for too long.

Generally, it would be very unwise to consider any bricklaying work to be done whenever the temperature jumps to a certain level which would be considered to be very inconvenient to work in. Interior works like remodelling of fireplaces can be tackled so long there is a warm space to mix the mortars while also keeping the materials at an indoor temperature. Bricklaying works that have, however, been completed during the colder months should be subjected to a very close inspection as well as looking for potential damage that can be caused to existing works as a result of the harsh weather.

As a home or property owner, you’re generally allowed to build next to your neighbour’s fence as long as it’s on your own side of the property. With that in mind, there are certain laws that regulate how close a fence can be built to buildings on the same lot or neighbouring lots. In addition, there are also local bylaws that provide limitations on the placements as well as height of fences so as to address safety hazards. In this post, we’re going to give you a good insight into how close you can build to your neighbour. Let’s take a look!

In general, if the fence is in your boundary then you’re allowed to build a 2-metre high brick or wooden fence or wall. However, this may differ depending on your location in the UK. As a result, you may want to reach out to your municipality’s building department in order to determine what these rules and limitations are in your area. In the events whereby there are no such restrictions but you’re still concerned, you can try informing your neighbour what your concerns are. However, if they’re not receptive there are some steps you can take to ensure your plans go as smoothly as possible. These steps include the following:

• Ensure to leave sufficient space for both the posts and footings
• Stagger your fence posts in order to make sure you’re not digging your neighbour’s
• Consider using concrete posts as they’re much stronger and will last a lot longer
• Use kickers or plinths for raised gardens and flower beds
• Make use of concrete plinths as they won’t rot over time like a wooden fence.

Smart EV charger is basically a set of functionalities in EVBox charging stations which allows the owner of the station to run several charging stations in a manner that’s cost effective and energy efficient. The word “smart, technologically speaking can mean a number of things, but generally it simply implies automation or your device’s ability to connect to other devices. Talking of smart ev chargers, this enables your charger to communicate with your car, the electric grid, as well as the ev charging infrastructure or other chargers. In other words, this means that any time you plug in your car to charge, the charger is able to transmit data to the charging operator. This operator can then make use of this data to identify the best time for you car to be charged and as a result, puts much less pressure on the grid and could also turn to be very cost effective in the long run.

Here are some of the primary benefits of smart ev charging

• They’re a lot quicker than three-pin plug. This is perhaps the most obvious benefit you can get from a smart ev charger. Overall, the charging time is much shorter due to fact that it possesses up to 3 times the power of a three pin plug.
• Schedule the charging to suit your lifestyle. If your ev home charger is connected to the internet, there are additional benefits you can derive from it. These includes being able to sync it with your calender. Once you add your schedule to the smart charger app, your ev will be well charged and ready to go any time it’s needed.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

Asbestos fibres are very small, so they’re not possible to identify with the naked eye. However, they’re common in particular materials of a certain age, so you can work out if there are any parts of a building that are likely to contain asbestos.

Start by checking the date that the material you suspect contains asbestos was installed. If it was in 2000 or after then you don’t need to worry, it definitely doesn’t contain asbestos. However, if it was fitted before 2000 it may contain asbestos, particularly if this was between 1940 and 1980.

Materials that used to commonly contain asbestos include ceiling tiles, guttering, soffits, fascia, external cladding and facades, vinyl flooring, artex, cement roofs and insulation.

Can You Use Floor Tiles On Walls?

Some floor tiles are so lovely you just can’t help but wonder if its safe to be used on the walls as well. If you’re also thinking along the same line, you’re not alone! Several other home and property owners are busy finding answers to this particular question. Now let’s look at the possibilities.

Generally, any tile designed as a floor tile by the tile manufacturer can also be laid on the wall (vertical surfaces) as well as countertops. Due to the fact that the floors are usually subjected to greater use than the walls in terms of foot traffic, the durability required is also considerably greater. Therefore, a floor tile with Abrasion Resistance values ranging from I - V is suitable for wall installation. However, you should take note that exterior wall applications must be different from its interior counterparts and must only be incorporated on tiles that are frost resistant.

There are two other factors that must be taken into consideration before you install a floor tile on your walls which includes the weight of your tiles per m2 as well as the strength of the surface in which the tile is to be installed. If you don’t want your tiles falling off, the combined weight of the tiles with the adhesive and grout should not be more than the maximum weight required per m2 (20kg to 35kg depending on the wall substrates).

Now that you have an idea of the possibilities of installing floor tiles on walls, it must, however, be said that reverse is the case when it comes to installing walls tiles on the floor. Wall tiles are, generally, not suitable to be laid on the floor as they are mostly non-vitreous ( can not withstand excessive impact, abrasion or thaw cycling).

If you’re about to fit a new bathroom in your home, then you’d probably be wondering how much would be the labour cost of getting it done. Unfortunately, a single accurate answer can not be provided to this question as there are many influencing factors that can determine the labour cost to fit a new bathroom. In this guide, we’ll give you a good insight on the labour cost of installing a new bathroom.

While you can obtain a good evaluation when planning the work on your bathroom, the final cost can largely vary. For small jobs such as fitting a pedestal basin with taps, professional installers can charge within the range of £170 to £250. Meanwhile, bigger projects such as tiling an entire bathroom can cost an average fee of about £70 to £90 per square metre. Generally, the overall average cost of fitting a new bathroom is about £6,500 in the UK. But in an event whereby you’ll be switching to a bathroom suite that’s exactly like the old one which wouldn’t require extra flooring as well as tiling, there’s a high chance you may be able to complete the project for a significantly lesser price.

The main reason why the labour costs vary is due to the fact that each individual job will have to be priced based on its own particular requirements and circumstances. Other influencing factors that’ll affect how easy a job is to complete, how much material will be incorporated and the duration of the project includes the size of the bathroom in question as well as the shape. However, there can be unforeseen complications like damaged piping which will also raise the price of the project and more.

Aeration, like scarification, is another vital step to keeping your lawn looking healthy and vibrant. It involves making small holes in the soil to allow air, water and nutrients to get into the grass roots, helping them to grow deeply, and produce a much stronger lawn. It also helps to relieve compaction from the soil, which stops nutrients and air from circulating. But how do you aerate your lawn?

Before you start to aerate your lawn, it’s a good idea to scarify it first to get rid of any moss, dead grass and thatch. This involves vigorously raking your lawn to get all the organic matter up, then transferring it to your compost heap or disposing of it. Light scarification is best in the spring but you can heavily scarify it in the autumn.

If you’ve got a small lawn, you can use a hand-held hollow tine aerator or even a normal garden fork. Dig deep into your lawn’s surface with the fork, or push the aerator into the ground which will pull plugs, or cores, of soil out of the ground to create air holes. You can let the cores dry and then go over them with a lawn mower or rake to spread them evenly across your lawn. This will recycle all the nutrients in those parts of the soil and stimulate bacterial activity to break down unwanted thatch. Don’t leave them, because they will make your lawn look bumpy over time.

If you’ve got a larger lawn, you might find it easier to see if you can hire a petrol aerator. But there are also rolling aerators that have spikes on a cylinder and you just push along, or even aerator sandals that you can wear and just go to town on your grass!