Find a Shop Fitter you can trust in Ripley.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

No, pattern imprinted concrete shouldn’t be slippery. Most good driveway installers will add a special anti-slip agent to the sealant before they brush it onto your driveway, so it will stop it from being slippery.

It’s important to ask a driveway company how they will seal your driveway when you get a quote from them. If an untrustworthy company seals your driveway badly, it can cause a thick and extremely slippery surface, so it’s vital that you ask any contractor what their procedure is before you engage them.

It’s also important to remember that pattern imprinted concrete isn’t a ‘non-slip’ surface – it’s just not slippery. You could still slip over on a concrete driveway, just like you could on tarmac or a block paved driveway. Also, once you’ve walked and driven over your driveway for a few months, its skid and slip resistance will increase as it weathers and builds up tiny specs of dirt on it. Pattern imprinted concrete is often used in high footfall areas in places like shops, fast food restaurants and theme parks, so if there was a significant slip risk these businesses wouldn’t use it.

You might think that you could ask your contractor not to seal the driveway to make it less slippery, but it could actually do the opposite. By sealing pattern imprinted concrete, it means that moss and algae is much less likely to grow, which can be extremely slippery to walk on if it’s left to its own devices. If moss does form on your driveway, the sealed surface is much easier to clean as you can simply pressure wash it away; this is not as easy to do on a non-sealed surface.

Yes. Commercial architects can provide a wide range of extra services such as project management, site feasibility studies, and help with site purchase. They can also be a great source of information and advice throughout the design and build process.

When it comes to conservatory air conditioning, a huge mistake you’d not like to make is to purchase and install a wrong sized HVAC system. When that happens, not only will you be left unsatisfied, but you’d also end up incurring much more expenses than necessary. If you go for an AC unit that’s too small, it won’t be powerful enough to cool your conservatory as you would like. However, when you go ahead to select an oversized AC unit, your conservatory would be cooled relatively quick but will leave the air in the structure with excess humidity and consume more electricity as it’s going to cycle on and off which will ultimately cost you more money. In other words, it’s always a smart decision to take your time to calculate the right air conditioner size for your conservatory before you make a purchase decision. So how exactly can you go about the determination of the appropriate HVAC unit size for your conservatory? Let’s take a look!

• Take the measurement of the conservatory’s square footage using a tape measure. If the space isn’t rectangular or square in shape, simply divide the conservatory in section comprising both squares and triangles which you can measure.
• Calculate the conservatory’s square footage. For a square or rectangle, simply multiply the length by the width. However if your space is in another shape, you can determine the square footage of the triangular sections by multiplying 0.5 by length and width, and the sum each of the sections.
• Determine the cooling capacity required for the space in question which is measured in British Terminal Units (BTUs)/hour. For more information to determine the BTUs needed depending on your conservatory size, simply visit the United States Department for Energy Star.

It can be quite tricky knowing the right time to purchase and fit an air conditioning system, however if you get the timing right, this can go a long way to help you save both time and money. It’s important to note that different individuals usually have varying needs - like it it’s possible your existing unit just broke down during the summer months or you’re carrying out some renovations during spring.

In general, there’s the need to put a couple of factors into consideration in order to make sure you AC installation is a hassle free experience. The best time to install an air conditioner is actually before the construction of the house. Several high set homes do not possess the space to fit fully ducted air after building. And even if there’s space, accessing the ceiling and down into the floors can be pretty expensive and difficult.

Installing an air conditioning unit earlier would mean less plaster would be required later down the road. A good air conditioning installer or HVAC expert should also advice you on the best location for the unit in order to help you maximize cooling in the summer and heating in the winter. Most importantly, if your AC unit is built into your house’s design, you’ll be able to save more money in the long run. However, you may not be able to fit a unit when constructing or renovation, therefore choosing the right time would be a question of, when is the right time of the year.

Generally, choosing a month in the off-season is actually a much better time to fit an air conditioner, but ensure that it’s the right time. Overall, the best time for an air conditioning unit installation is autumn when the demand is at its lowest. Since retailers are usually overstocked with units after the summer months, you can get yourself some nice discounts

What Is A Septic Tank?

Septic tank may be a very strange concept to many individuals, but to the households that make use of them - they’re crucial to several homes especially the ones who are not connected to the mains sewage line

A septic tank .is simply an underwater sedimentation tank which is incorporated for the treatment of waste water via a process called biological decomposition and drainage. The tank utilizes natural processes in conjunction with tried and tested technologies for waste water treatment. The waste water comes from household plumbing which are often generated by bathrooms and toilets, kitchens, laundry as well as drains.

Septic tanks usually possesses a very simple design. They are simply underground containers that are watertight ( usually round or rectangular) made of plastic, fibreglass or concrete. They normally constitute different compartments which is a T-shaped outlet to prevent the sum and sludge from escaping that tank and finding a spot on the drain field area.

Septic tanks are particularly useful for households with a poor drainage system or those that aren’t connected to the mains sewage system. They serve as their main source of safe waste water disposal. The tanks work by collecting waste water and excreta in one huge underground tank and they happen to be very common in rural and developing areas.

Septic tanks are typically fitted underground and 50 metres away from the building. For those that live in towns and cities, septic tanks are mostly not needed as the waste water is normally transported and taken care of by their sewage system is is maintained and managed by a local water company. If you own a septic tank, you have an extra duty to make sure that it’s existence doesn’t negatively impact the environment.

Home electrics can be extremely dangerous and it’s very unwise to try and carry out repair work or maintenance yourself without the necessary knowledge and skill. Therefore we would always recommend using a Part P registered electrician at all times.

Are you thinking about updating your bathroom? If yes, then you’d probably want to know how to go about it. Well, when it comes to bathroom remodelling, the process always begins with the drawing of a floor plan. If you don’t know how to go about that, then you’ve come to the right place! In this guide, we’re going to take you through the bathroom floor plan drawing process. Let’s take a look!

First and foremost, you can make use of the pencil and paper approach as it happens to be much cheaper than the computer based approach. Plus, you don’t have to be an art genius in school to complete the task satisfactorily.

1. Sketch it out. Create a rough sketch of the space on unlined paper. This should feature all openings like the doors and windows, the spots where the existing plumbing fixtures are located, the location of the electrical lines including outlets, receptacles, heating and cooling pipes and more
2. Add dimensions to the sketch. The next line of action would be to take measurements of the bathroom. With the help of a friend, hold the tape tightly at both ends in order to get the right dimensions. Then, measure the length of the walls, fixtures, windows and mark then roughly on the sketch. Once done, you can go back to double check the recorded measurements for accuracy.
3. Transfer the room dimensions to a sheet of graph paper. At the stage in the process, you should be aware that each 1/4 inch square on the graph paper is equal to 6 inches or half foot. You can start by drawing the bathroom walls and partitions as well as the surrounding areas. Then, add the doors and the direction they swing open and the windows present. Once done, draw the fixtures to complete the floor plan.