Find a Shop Fitter you can trust in Stanford-le-hope.

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.

Generally, you wouldn’t need to get in touch with a quantity surveyor prior to purchasing a property, unless of course your property is a very unique and unusual one. After making a commitment to buying a property or to kick start a construction project, then you might want to start taking into consideration getting in touch with a quantity surveyor. The best time for a quantity surveyor to carry out an inspection of the property is right after settlement and just before the tenants moving in. This is to ensure that the quantity surveyors do not disturb the tenant and they also get to fully go through what you’ve purchased as well as the condition it’s in.

Quantity surveyors will help you by working with architects, accountants, engineers, building owners, builders, developers, financiers, government, insurance underwriters, loss adjusters, sub contractors as well as solicitors. What’s more? The in depth knowledge quantity surveyors possesses when it comes to construction costs enables them to carry out a number of useful tasks to help you.

Prior to construction, quantity surveyors can prepare a feasibility study, estimate to defined the project budgets, carry out an analysis to refine the budget as the design documents develop, prepare Bill of Quantities so as to help with the tender process and also to carry out a review of Builder’s tender submissions. While the construction is ongoing, they can help provide cost control services, carry out an assessment of the builder’s progress claims and also undertake an assessment of variation and delay claims. Finally, after the construction, they can assist with the determination of the final project cost, prepare the tax depreciation reports for both investors as well as property owners and also prepare Expert Witness reports to assist in the settlement of building disputes.

Over the years, UPVC spray painting has grown to become a standard practice. Previously, what was done when people wanted to change the colour of their UPVC window is simply to replace the old ones. However compared to the cost of replacing the units, it’s actually a lot easier to simply have your UPVC windows sprayed and even more importantly, at just a fraction of the replacement cost. If you’re thinking about spraying your upvc windows, then you’ve come to the right place! In this post, we’re going to take you through the entire process. However, if you lack the confidence needed to pull this off, we’d strong advise that you get in touch with a professional to avoid make costly errors or mistakes.

The first step to successful upvc window spraying is always to make sure that the upvc is properly cleaned by removing any loose dirt and residue, getting rid of any muck and grime which has developed over the years. You can also abrade the surface in a very light manner to leave upvc frames with a key to make the paint adhesions stronger. Once you’re done with the preparation, the obvious next step is masking off. This process requires you to protect the walls, glass, floors and brickwork from any potential over spray. To achieve this, you can make use of masking papers.

Upon completion of the masking off process, then its time to spray paint the upvc windows using a spray gun and spray painter. This requires a lot of practice as it could be very dangerous as you can inject yourself with paint, which can be seriously fatal.

If you’ve ever looked into different types of conservatories, you’ll see that wooden conservatories are not the cheapest. However, that’s not a reason to dismiss them as an option for your home.

Wooden conservatories can cost anywhere between £15,000 to £60,000. While this may seem expensive, they are often a much classier option for your home and are ideal for period homes and those in a conservation area where uPVC might not be permitted.

If you choose a hardwood conservatory, you could see your conservatory last over 15 years. Most uPVC conservatories will only last around this time, and as they get old they can look shabby; it’s common for the frames to discolour in the sun. With good maintenance, wooden conservatories can look fabulous for years. Wood naturally retains heat too, so ensure that you use low-e internal glass which reflects heat back into the room and you’ll have as warm a conservatory as any.

When you weigh up all of the pros and cons of uPVC conservatories compared with wooden ones, you might come to the conclusion that wooden conservatories aren’t that expensive when it boils down to it. Although the initial cost is higher, you’ll get a better-looking conservatory that works with both modern and period properties and will look elegant and tasteful for years to come.

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

How To Clean Roof Tiles?

If you’re a DIY person with a dirty roof tiles or just a homeowner who’s also a lover of knowledge, you may probably like to know how you can have your roof tiles cleaned. This is a very common question which often depends on the dirt or debris you’re dealing with as well as the type of roof you possess. Most often than not, if you own a traditional concrete or slate roof tiles, then you’re more likely to battle moss and or algae growth.

If you’re not a competent DIY person or do not have enough confidence to pull this off, then it’s advisable to hire the services of a professional who can guarantee the best results for help. In this article, you’ll learn how to go about cleaning your roof tiles. Let’s have a look!

✓ Consider Safety. When it comes to roof cleaning, you have to be very careful. They’re normally high up and any task that deals with height will usually require putting safety measures in place. Firstly, it’s important to be confident with heights and ladders, if not you’d have to find someone who is. And if you’re confident, there’s also the need to find someone who can help you hold the base of the ladder.

✓ Trim the trees. Nearby trees are usually a threat to any roof and also makes cleaning much harder. So it’s always wise to cut any overhanging branches before you proceed.

✓ Bleach or not to bleach. Although you have to be very careful using beach and water but it also happens to be one of the easiest DIY ways to clean your roof. You either stand about 4 feet away and rely on water pressure or clean down the tiles by hand.

✓ Try not to make use of a blaster.

Check your Price's door installation cost calculator and charges guide will allow you to estimate both typical labours only costs for door hanging & installations, renovations and repairs as well as the total estimate for comprehensive door installation projects.

• Door & Frame Installation Job and the average Cost in £'s

• uPVC door installation including glazing & architrave costs around £90 per door

• uPVC french & patio door sets including glazing & architrave costs around £120 per pair

• Softwood french & patio door sets including architrave costs around £180 per door

• Hardwood french & patio door sets including architrave would cost around £250 per pair

• Softwood internal door hanging only would be around £40 per door

• Hardwood internal door hanging only would set you back around £48 per door

• Softwood external door hanging only is around £60 per door

• Hardwood external door hanging would cost around £70 per door

• Locks, letterboxes & door furniture timber doors are around £15 per Item

• Glazing £15 per pane

• Brick cut-outs single doors is around £60 per cut-out

• French or patio door brick cut-outs will be around £90 per cut-out

• New lintels will cost around £150 per lintel

Door Repair Costs and Charges

Estimate door mending labour charges by totalling the unit costs of the mandatory jobs. The complete door repair cost includes the total labour charge plus the cost of all parts, fixtures and fittings. A call out charge may be added on jobs totalling less than £100.

Average Cost of Door Repair Job

Replacement glazing units for uPVC doors will be around £15 per unit

Replacement glazing units for timber doors is around £20 per unit

Replacement door glass pined & putty will cost£30 per pane

Replacement handles are around £10 each and general repair work will cost you £25 per hour

Building & FENSA certificate charges

FENSA certificates are obligatory for maximum door replacements and new build setting up prices differ from council to council.

Average Cost of Window Repair Job: One to two doors will cost around £85

Average Cost of Door Fixtures & Fittings Removal Job

Removing internal doors will cost around £10

Removing internal door liners will cost around £15

Removing external timber doors will cost about £10

Removing External timber door frame will be around £20

Removing external uPVC door & frame removal will be around £30 and Rubbish disposal will cost £150 per ton.

1. Start in one corner of the sub-frame and position the first board across the inner joists. You want the deck board in the opposite direction to the inner joists, ensuring that it’s flush with the frame. Position any end-to-end joins between the deck boards halfway across an inner joist so you can screw both boards into the joist for stability. Make sure you keep a gap of between 5-8mm to allow for expansion of the wood.
2. Begin to screw your deck boards to the joists. You’ll need to secure the deck board to every joist is covers along your deck frame. Use two screws for every joist. Mark where you’re going to add your screws, ensuring that they are at least 15mm from the end of the board and 20mm from the outside edges. Drill pilot holes for the screws, being careful to only drill through the deck board and not the joist. Then screw the decking screws into the holes.
3. Continue to screw in the deck boards, ensuring you leave the correct expansion gap. You can stagger the deck board joins across the deck for more strength.
4. Sand down any cut ends if you need to before applying decking preserver to protect the timber from rotting.