Find a Shop Fitter you can trust in Walton On The Naze.

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

The number of sensors you need will depend on the size of your home. Most alarm systems feature 2-4 passive infrared sensors (PIRs) for motion detection, and 2-4 magnetic contact sensors on doors and windows. An alarm company will advise you of how many your property will need upon an inspecton.

If you’re looking to hire the services of a house cleaner for your residential property, then one of the first things that naturally comes to mind is the cost of completing this task. Simple as it seems, there’s actually no short and direct answer to this question as the price of your clean will depends on a number of varying factors. Generally, the key drivers of the amount you’ll have to pay for your clean includes the following: location, number of rooms, frequency of cleans, the cleaner’s experience, number of cleaners in the local area, number of bathrooms, agency charges as well as optional extras.

There are two main routes you can take to hire a cleaner. These routes include using a cleaning company or agency, or source your own independent cleaner. Whichever way you choose to go through, it’ll automatically play a role in the price you’ll have to pay to get the cleaning service. In general, you can normally expect to pay between £4 to £10 per hour in agency fees in addition to the rate the average cleaner would expect for the area, based on how competitive the market for agencies is in your area.

For hourly cleaners, the cost you can expect to pay to have your house cleaned typically ranges from £12 to £23 average cost per hour. Prices in more rural areas tend to vary a lot more, which is mostly dictated by the number of businesses that are operating in the area.

There are a number of ways in which you can save money on your clean which includes supplying your own cleaning product or equipment, opting out of optional extras like oven cleaning or ironing, comparing quotes from different provides to get the best price and more.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.

Various studies have suggested that CCTV is an effective deterrent against home burglaries. In the event that a crime is committed on your property, well placed CCTV means you’ll have the evidence to help the police. It has been recorded consistantly that since CCTV systems have been installed, localised crime has fallen and has lead to more arrests.

How To Lay Wall Tiles

Laying of wall tiles is a task that should be done with great caution, especially if you’re working on a tight budget. It is guided by its own unique set of rules which you do not dare to break if you wish to get it right the first time, and also to avoid incurring some additional costs. If you do not have a proper training or experience, laying of wall tiles is better left to a skilled professional for the best possible outcome. However, this guide will walk you through the various steps in the process to help improve your knowledge. Let’s get started!

lPrepare The Wall Surface

• Make sure the surface is clean, dry and smooth

• In wet areas, wall tiles should be fitted over a backer board

• If it’s a painted wall, ensure to sand the surface before installation.

lCreate The Layout

• Locate the centre of the wall

• Create an intersecting vertical and horizontal layout lines using a level

• Ensure to include spaces for grout joints when creating the layout.

lApply The Adhesive

• For wet areas, makes use of thin-set adhesive that’s cement-based.

• For dry areas, you can use pre-mixed mastic adhesive

• Follow the manufacturer’s instruction to prepare the adhesive

• Using a notched trowel, apply the adhesive (hold the trowel at about 45 degrees angle)

• Ensure not to cover the layout lines with the adhesive

lInstall The Tiles

• Follow the layout lines to install the wall tiles

• Place the full tiles firmly on the adhesive and twist slight and gently to make them fit.

• Use tile spacers to ensure constant gaps for grout joints.

lCut The Tiles

• After installation of the full tiles, there’ll most likely be a need to cut some tiles to fit.

• Cut the tiles with a wet saw or manual tile cutter

lGrout The Tile

• Ensure the adhesive is well dried and remove the tile spacers.

• Prepare the grout as instructed by the manufacturer.

• Use a rubber gloat to apply the grout.

• Remove the excess grout from the tile surfaces

• Wipe the tiles and joints gently using a grout sponge and clean water.

When you build a new wood-constructed conservatory, or any type of conservatory, you’ll need to dig a trench for the footings. You’ll need to dig to a minimum depth of 600mm and at least 300mm below your property’s damp proof course. When you dig down, you might expose obstacles such as underground pipes.

If this happens, you’ll need lintels for your wood-constructed conservatory. These are usually concrete and protect the pipes or obstructions from being crushed. You may also want to use steel mesh for additional support.

Building Regulations state that if an opening is formed in a wall, the structure above the opening needs to be supported. This will be especially relevant if you’re building a wooden lean-to conservatory. It says that there are two ways that you can use lintels to provide support.

The first way involves using a steel lintel to support both the inner and outer leaf of a cavity wall. It can then serve as a cavity tray that directs moisture from the cavity through the outer skin of the wall as well.

The second way to use lintels is to use two steel or concrete lintels. They support each leaf of a cavity wall construction. You’ll need separate thermal insulation and a cavity tray as well.

Whatever type of lintel you use, it should have a suitable bearing onto the wall at each side. If you’re not sure, speak to the manufacturer of your wood-constructed conservatory, or ask a reputable company to install it for you.

Central air conditioning system is a system which operates by cooling air at a central place and distributes the cooled air to and from rooms with the help of one or more fans and ductwork. What makes the whole idea of air conditioning feasible is the operations of the air conditioner compressor. When it cooling gas is compressed, it allows it to absorb heat from the house and blows it outside into the outside air and that’s exactly how the cool air is being generated.

Central air conditioning are of two main types which includes a split system as well as a packaged unit.

Generally, in the split system AC unit, both the condenser and compressor are included in the outdoor metal cabinet, whereas the indoor cabinet includes the evaporator. Typically, in several split system air conditioning units, the indoor cabinet will also include an air handler or a furnace. What’s more? The evaporator coil of the AC unit is fitted in the cabinet or the furnace or heat pump’s primary supply duct. This type of central air condition is usually the most economical AC unit to fit if you already have a furnace in your home.

However, in a packaged central air conditioning system, the components including condenser, compressor and evaporator are all included in one cabinet. Supply of air as well as the return ducts are connected through the home’s exterior wall or roof to the package central air conditioning system - mostly placed outdoors. This type of central air conditioners also features electric heating oil or a natural gas furnace. With this perfect blend of central heater with air conditioner, there’s simply no need to a separate furnace indoors.