Find a Shop Fitter you can trust in Witham.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

For some types of asbestos, you are not legally required to use a licensed contractor. However, it’s recommended that you always use one. These contractors will have all the relevant training and knowledge to make sure asbestos is removed safely. The Health and Safety Executive (HSE) is the licensing body.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

If you’re interested in getting a replacement door, you may want to know just how long it’ll take to fit your new patio door. However, there’s no specific answer to this question as there are different types of patio doors with all having unique installation processes as well as varying completion times. Generally, fitting patio doors will normally take within a range of 10 days to 21 days, except in situations whereby you have specific and non standard requirements. The time range provided represents the total duration starting from ordering the patio door till the installation is completed and this also varies from style to style.

If you want to get a professional double glazing surveyor, he will assess you property while also making sure the right and accurate measurements are taken and also plan out the installation. In order to avoid any unnecessary delays, this is a very crucial step as the surveyor will work to make sure any potential problems is identified early on. Once done, you can then wait a couple of days for the door to be manufactured and then fitted, depending on the door style and finish.

The time to completion varies depending on the complexity of the design. Patio doors may take about 14 days to 21 days with bifold patio doors being the most complicated and time consuming. This is due to the fact that they take longer time to manufacture and when you factor in the possible duration of the installation, you can expect a total duration between the range of 6 weeks to 8 weeks.

In addition, there are also some other factors that can affect the time it takes to install patio doors. These includes the need for a higher energy rating, upgraded security fittings, door hardware with custom finish and other special requirements that are beyond the standards.

There are a wide range of household rubbish and wastes you can put in a skip. But unfortunately though, paint cans and leftover paints isn’t one. Furthermore, not only is a liquid paint restricted from skips and landfills, but they are also banned by the council. Frustratingly, because it’s hazardous to the environment and blockages it can create in the pipe, pouring paint right down the drain is never an option as well. So what then is the best way to get rid of your leftover paint? Surprisingly, you have quite a number of options which we’ll share with you.

• Is the paint unused and unopen? For unopened paints, you can simply return them back to the seller either for an exchange or for a refund. Obviously, this will require a receipt and if unavailable, then you might want to consider the other options below.

• Is it just little paint leftover? Since it has been specifically banned from skips and it’s just a small amount of paint, you can get a bit creative with the disposal method. Simply get a cardboard or other papers, paint it with the remaining paint and dry it out. Once dried, you can then dispose the cardboard or paper alongside other permitted wastes in the skip.

• Is it a large amount of paint? For large amounts, you can contact some of your friends or family who might need it to get the paints off your hands. If you are unable to dispose any or all, there are online platforms like Freegle or Freecycle where there are people willing and ready to get leftover paints in large quantities.

• Is it unusable? If positive, then the giveaway option is completely neutralized. The best bet here is to leave your paint out to dry if it has gone past its usable days, then take it to a household waste recycling centre.

Click here to learn more about skips.

How Many Solar Panels And Batteries Do I Need?

Are you presently considering adding a solar system to your home? With several homeowners in the UK using solar now, many more are realizing the numerous benefits they stand to derive by getting one. Therefore, if you’re thinking about adding the system to your home but do not know where to start, you’ve come to the right place.

Here, we’ll help you calculate the number of solar panels and batteries you’ll need to power your home. Starting from the panels, you can begin by taken into account everything that makes use of power in your home to get a good idea of how many you’ll need.

• Firstly, you’ll have to determine the number of watts you use. Simply go through your utility bill for kilowatt-hours (kWh). This varies amongst homes and being able to identify your daily average energy usage will assist you in getting your solar needs.

• Secondly, you have to determine the peak sunlight hours - having in mind that the solar panels only work when under direct sunlight. Once determined, you can then multiply the figure in hours by your home’s hourly energy usage and divide by your selected solar panel’s wattage.

Generally for a 1500 square foot house, you might need around 15 to 18 solar panels to cover the house’s electricity.

Meanwhile for batteries, there are also some factors to be considered to determine the number of batteries you’ll need for your house. These factors include your home’s power or electricity usage, the period of time in which the battery will be used as well as the battery’ specifications. Once done, you’ll be able to calculate the number of batteries required by your home.

Artexing a ceiling can be a tricky job, but whether you’re considering hiring a professional or DIY, it’s helpful to know how it’s done.

Artex is available either in a paste or powder form. The paste is ideal if you’re making small repairs or additions to an existing ceiling. But, if you have a whole ceiling to cover, the powder is more cost effective. When you’re ready to get started, you’ll need to mix the powder up with cold water according to the instructions.

It’s possible to artex over plaster, plasterboard or paint. If you have a plasterboard surface, you should tape and fill any joints or cracks before you begin. Plaster and plasterboard both require a coat of sealant or primer first. You can usually artex straight over paint, but any gloss paint should be sanded down, and any dark paints covered with a layer of white.

Artexing can get quite messy, so make sure you empty the room you’re working in as much as possible, lay down sheets and wear protective clothing and glasses. You might want to practice on a piece of board before you start on the ceiling.

Start by using a brush or roller to cover a 500 square cm area with a generous layer of artex. Then use a brush, comb or roller to create your chosen texture. Every time you do a new section of ceiling, try to blend it with the other sections you’ve done. Don’t be tempted to cover the whole ceiling before you start adding texture – the artex will dry too quickly for you to do it all in time.

Artex usually needs 12-24 hours in a well-ventilated space to dry completely.