Find a Shop Fitter you can trust in Hertford.

Once you’ve chosen the perfect feature to suit the shape and style of your bathroom, it’s time to start putting it to good use. Read on for a step-by-step guide on how to install a bath, but first of all, below are the preparatory tools;

Preparation

Before you install a bath, there are some things that needs to be taken into considerations.Once you have decided where you are going to install your bath, use an electronic detector to make sure there are no hidden pipes or wires in the walls where you will be securing the fittings. It is also advisable to choose walls that have a stud so that you can attach your fittings so strongly.

When assembling your bath, lay it on top of a rug or blanket to ensure it doesn’t get scratched, and remove any protective film from the areas you will be working on, such as around the drain and tap fittings, as well as the sides where the bath will sit against the wall. Always turn off the water at the mains beforehand.

Note: The installation process will vary, depending on the design of your bath. It is always necessary to consult the manufacturer instructions alongside this guide.

MATERIALS

• Drill and appropriate drill bit
• Screwdriver
• Spirit level
• Tape measurer
• Hammer
• Pencil
• Caulking gun and silicone sealant

You’ll also need an extra pair of hands to help manoeuvre the bath into place.

Step 1

Attach the legs and the fittings by securing the appropriate bolts and channels, and then attach the feet.

Step 2

Measure and adjust the bath's position, Once you are sure that your bath is level, mark the places where it will be secured into the walls and floor. If your bath comes with wall fittings, use your pencil to mark the place where they will be secured to the walls. Do the same for the floor fittings.

Step 3

Prepare the wall for the fittings, align it with the wall at the location you marked and use your spirit level to make sure it is even. Drill holes and secure in place, making sure you use fittings that are suitable for the type of walls in your bathroom.

Step 4

Secure your bath by moving the bath back into the final position and align it with the holes you created, or on top of the timber batten. Once again, check that it is level. Turn the water back on and check for any leaks.

Step 5

Seal around the rim, fill it with water and trace silicone sealant around the edges, where the rim meets the wall. Allow it to dry for the recommended time.

Smart controls such as Hive are the next generation technology with more and more people now converting their houses into smart homes to control multiple devices in the homes remotely. Smart technology can be incorporated with several household devices such as security, lighting, entertainment and more. But what if there’s an oil boiler installed in your home, can you still connect your Hive with the your heating? Well, simply read on to find out.

The answer to this question is yes, most oil boilers are compatible with Hive and can substitute for either an existing conventional programmer or thermostat. The smart technology works to help derive more benefits from your heating system and they usually come with apps which can be used to control your home’s heating from anywhere with just your mobile device. Hive, however, cannot work to replace the functions of smart oil boiler heating controls to modulate your heating as they only work on an on or off basis. To make use of the modulating technology in an oil boiler, the cost of manufacture would be considerably higher while offering little advantage in efficiency for the home or property owner. Ultimately, this implies that you can’t incorporate smart technology to control the output in a similar way as a gas boiler, but there are still some ways to utilize smart technology with your oil boiler in such a way to boost your efficiency and lessen the energy bills.

Do you want to use your Hive with your home’s oil boiler? We’d advise you get in touch with an OFTEC qualified engineer if you wish to install Hive Active Heating on your oil boiler, as British Gas engineer do not offer this service.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

You should inspect your roof twice a year, ideally after rain or snow, to see if it’s draining properly. Also in the Spring to check for damage that may of been caused over the winter months that will need to be put right before the next winter. Have an inspection carried out if you are unsure.

If you’d like to hire a residential architect, but have limited funds, there are several things you can try to reduce their quote.

Firstly, you don’t necessarily need to hire them for project management – you could just ask them to do the design. This will mean you’ll have to do some extra donkey work, but you could choose between finding a cheaper professional to do your project management or simply doing it yourself.

There might also be other architectural services that you can cut down on. Some professionals offer extras like landscape, interior and detailed joinery design. If you can do without any of these, this will help to reduce the overall cost.

You could also think about scaling down your project. Lots of residential architects work out their fees as a percentage of the total construction cost of your project. Lower the cost of this, and your fees might go down too.

If you find out there’s asbestos in your property, it’s not always necessary to remove it. Asbestos is relatively low-risk if it’s contained in a material. This means that, if the material it’s in is in good condition, it shouldn’t be a problem.

However, if a material containing asbestos is damaged, or you want to remove, sand or drill into it, it’s best to have it removed by a licensed professional.

One of the major source of concern for several home and property owners in London when it comes to heating and cooling systems is whether its really necessary to use an air conditioning system throughout the year or just a couple of months a year. Well, if you’re also worried about the this, then you’ve come to the right place. In this post, we’re going to consider why making use of an air conditioning system is essential all-year round. Let’s take a look!

The short and simple answer to this question is, it depends. However, if you really want to have a total control over your own comfort at home, then the answer is yes. In fact, most individuals who have installed heating and cooling systems with the intention of only using it in July and August usually find themselves making use of it all through the year and having a more sound sleep than ever before. What’s more? London is known to have uncomfortable and inconsistent temperatures all year long. If you intend to use your system for a specified couple of months, you may just be shocked to discover when you’ll need it the most may be outside your selected usage period.

In a move to protect older properties or an apartment complex, most landlords in London usually won’t give permission to enable structural changes. As a result, this has given several Londoners the impression that they’ll have to just cope with the heat and cold all throughout the year. In this kind of situation, all that’s needed is the installation of internal air conditioning units which does not need any penetration through the exterior wall to be fitted.