Find a Solar Panel Installer you can trust in Blaydon-on-tyne.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

If you’re thinking of adding a solar battery to your home, you might be wondering whether or not it’s going to work in a power cut. If yes, then you’re not alone as this is one of the most common questions asked when it comes to solar batteries. In this post, we aim to provide you with a detailed answer to solve this concern once and for all.

The answer to this question is, it depends. The main reason why your solar batteries will usually not work or provide your home with the much-needed back up power is as a result of the several threats it poses. You should be aware that both your solar panels and battery are connected to the main grid. When a power cut occurs, your engineers will have to operate on the grid. If the solar panels or batteries are in operation at the period there’s a high chance the engineers would be electrocuted by the electricity that’s being produced. As a result of this, solar inverters are usually designed to automatically switch off once a power cut occurs. However, it should also be noted that if your solar battery possesses backup functionality, you’ll be able to make use of your solar energy in the event of a power cut. In other words, what determines if your home battery would work in a power cut is the availability or otherwise of a backup functionality.

Furthermore, you might also wish to know if your solar panels will continue to charge the battery in a power cut. Well, this depends on the type of backup system you possess. There are some more affordable batteries that are designed to automatically release their stored energy upon the detection of a power cut. And this is mostly because the battery inverter is usually smaller than the solar inverter which allows the energy from the solar inverter to the transmitted to the battery - risking an overload. However, if otherwise, then energy can continue to be transmitted to the battery until its fully charged.

In theory, you can fit solar panels yourself. In practice, it’s worth leaving it up to the professionals.

If you get DIY solar panels and install them on your roof yourself, you won’t be able to apply for the government-backed Smart Export Guarantee (SEG). The SEG pays you for every unit of electricity you generate and send back to the grid, so it’s a scheme well worth signing up for. However, you must have your solar panels installed by a Microgeneration Certification Scheme (MCS)-registered engineer or company, so you’ll miss out if you install the solar panels by yourself.

The other thing to consider about installing solar panels yourself is that you’re dealing with electricity. Electricity is extremely dangerous if handled incorrectly, so if you don’t have any qualifications in working with electricity you could be putting yourself and your family at risk. Connecting DIY solar panels yourself and doing it incorrectly could mean that you give yourself an electric shock or cause a fire. If your home is damaged due to a fire caused by solar panels you’ve installed yourself, it’s unlikely that your home insurance company would pay out.

Before having a go at installing your own solar panels, do some quick sums to see how much money it could really save you. A 3.5kW DIY solar panel kit will cost around £4,000-5,000. According to the Energy Saving Trust, a home in the South East of England where most occupants are out all day until 6pm would save around £100 a year on their electricity bills. That means that you wouldn’t break even until 40 years, but solar panels last around 25 years on average. However, if you have your solar panels installed by an MCS-registered installer and they cost £4,500, you could save £220 a year including your SEG payments. That brings the payback time to around 20 years.

So although the initial outlay is slightly less when you install solar panels yourself, it’s much better to have them installed by an MCS-registered engineer so you can take advantage of the SEG payments.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.

Solar panels can be pretty expensive, so require an initial investment. However, a quality solar panel installation can be very financially beneficial, saving you money in the long run. It does this in two main ways.

Firstly, using electricity generated by your solar panels means that you have to use less power from the national grid. Once you’ve bought your solar panels, your solar electricity is essentially free, meaning that you’re saving money by using this instead of power supplied by your energy company. If you want to maximise these savings, invest in a solar battery so you can store unused solar electricity ready for when you need it.

You can also earn money with your commercial solar panels through the Smart Export Guarantee [https://solar-panels.quotatis.co.uk/smart-export-guarantee/]. This is a government scheme that says that all licenced energy suppliers with 150,000 customers or more have to offer a tariff to renewable energy generators. When you generate solar electricity but don’t use it immediately it gets fed back to the grid – the tariff pays you for every kWh of this.

At the moment there’s no minimum tariff that an energy company has to offer – it only has to be above zero. However, many energy companies are competing to offer the best deal, so you can definitely find a tariff that will pay you for all the unused solar electricity you generate.

Not only will you reduce your electricity bill by generating your own electricity with solar panels, but you can also earn money through the SEG which is offered by large energy suppliers. They’ll pay you for the electricity you export back to the grid. You’ll also reduce your carbon footprint, lessening your impact on the environment.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.