Find a Builder you can trust near you.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Have you been advised by a structural engineer or a surveyor that your building needs to be underpinned? Well, this might just have you wondering what underpinning really is and how long it lasts. In this post, we’re going to tell you more about underpinning to help you make the best-informed decision possible moving forward. Let’s take a look!

Basically, underpinning refers to the incorporation of one of various methods to reinforce or repair the old foundations of a building or structure mostly to remedy or avoid subsidence. Now, subsidence can be caused as a result of poor soil quality, increase in the load on the foundation like adding a new storey, excavations below the building as well as inadequate foundation which is more common in older buildings. When an underpinning remedial work is carried out, there are a plethora of benefits that comes with it. It’s preserves the structural integrity of your building by strengthening it, make it a lot more attractive, increases the property’s value and makes it a lot safer for both you and your loved ones. So how long does underpinning last?

Well, many underpinning contractors will offer you a 10-year guarantee of its underpinning solutions for defects. Primarily, there are two reasons why underpinning can fail which is poor installation and fresh issues arising or unforeseen circumstances. While the first is an issue that can be avoided by employing the services of an expert contractor who possesses vast experience and knowledge in the field, the second can not be avoided. However, in the absence of the unforeseen issues, underpinning is expected to last for the natural life of the building, so far it has been expertly installed.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

How long it takes to install insulation will depend on the size of your property. In general, loft and cavity wall insulation can be installed in a day or two. External wall insulation will usually take longer to install. The rep or installer will be able to advise you when quoting for the job how long this will be.

If you’re planning to construct a kitchen diner extension, to help you set a budget and start planning you must first have a cost estimate that’ll complete the entire project. If not, there’s a probability that you may have to spend more than would have been necessary or probably break the bank to have the project done. In truth, there’s no single and short answer to this question as the cost of a kitchen diner is largely dependent of several variables. In this article, we’re going to give a good insight into kitchen diner extension cost so as to help you make informed decisions moving forward. Let’s take a look!

On the average, a kitchen diner extension will cost within the range of £25,000 to about £45,000, however if you happen to reside in London, you can expect the cost to be a lot more than that - closer to £60,000. And due to the fact that there happens to be a plethora of options out there, any decision to make be it on the size, tradesman, flooring, finishes or type of the kitchen diner extension, will have a considerable impact on the overall cost of the project. For instance, a basic kitchen diner extension cost can be within the range of £12,000 to about £15,000., while a high end kitchen diner extension can reach a whooping price between £80,000 to about £100,000.

The total cost of your kitchen diner project will rely heavily of the size as well as the quality of the finishes. For example, a kitchen diner extension that’s small and basic is likely to cost about £1,300 to £1,500 per square metre. However, if you’re going for higher quality finishes, you can expect to pay within the range of £1,900 to about £3,000 per square metre.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

It depends on the size and type of extension. Small porches or flat roof extensions are very reasonably priced. More substantial two storey extensions can be expensive. In general, the price is roughly proportional to the amount of space you add to your home.