Find a Builder you can trust near you.

Generally, it’s possible to extend a barn conversion, but there are certain conditions that you’ll probably need to meet. Ultimately, it’s up to your local planning office to decide whether to approve your planned barn conversion extension or not.

Typically, small extensions on the side of a barn conversion are often approved, particularly if they serve to preserve the original character of the barn. This could be because the extension will mimic the appearance of the original structure, or house facilities that would look odd in the original building.

However, you probably won’t be allowed to build a larger extension, or one that isn’t in keeping with the appearance of the original barn.

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

Typically, loft conversions do not require planning permission except in certain situations. They’re usually covered under what’s known as Permitted Development. Certain building works like loft conversion, rear extension and conservatories are granted planning permission by local authorities. Permitted Development, however, gives you a free range to improve your home without having any issues from the councils or regulations. Before your planned loft conversion can be covered under Permitted Development, there are some certain criteria that must be met. This criteria includes the following:

✓ The extension must not go beyond the existing slope of the roof at the front of the house.

✓ The loft space converted must not go beyond 40 cubic metres in a terraced house.

✓ The roof’s height must not be increased by the extension.

✓ The loft space converted must not reach beyond 50 cubic metres in a detached or semi detached house.

✓ The plan for the extension mustn’t involve structures like balconies, verandas or anything other structures of this nature.

✓ The roof extension should be positioned as far back as possible or at least 20cm from the existing eaves.

✓ The side that faces the window openings should be at least 1.7m beyond the floor and the windows should also be obscured.

✓ The roof extension must not overhang the existing roof or wall of the house.

✓ The materials that are to be used must be similar or the same to the materials that has already been used on the house’s exterior.

However, you should bear in mind that there are some properties that are exempt from Permitted Development. Examples of these type of properties include conservation areas, Areas Of Outstanding Natural Beauty and World Heritage sites. Permitted Development does not also provide coverage for listed buildings.

A double house extension is basically a construction to any aspect of your house that elevates up to offer two floors of space. It can be structured to suit your existing home in two storeys or as a side wing on a taller property. If you’re considering building a double house extension, then estimating the cost is a very important task to do before commencing the project. In this article, we’ll give you an idea of the cost of a double house extension so you can estimate yours accordingly.

The double house extension cost depends on several factors that’s specific to your home as well as your design choice. These includes:

• Location of your property. Places like London and the southeast will generally cost more than the other regions due to higher demands.

• Accessibility of the site. The ease of your site’s accessibility also plays a key role in the price.

• Size of the extension. The more the extension’s size in footprint and square metres, the higher the possible costs.

• Materials used in making the roof as well as the complexity of the roof design.

• Your choice of finishing. These includes flooring window and door frames, glazing, underfloor heating and roof lights.

• Your property’s soil type. Different types of soil requires varying treatments as well as materials to develop solid foundations.

Constructing a double house extension is a quite simple build in terms of technicality when its to the side or rear of your house as this can also help you save some money. Generally, considerably expanding your home’s space by building a double house extension will cost within the range of £1,500 per m2 to about £2,800 per m2.

Cement is a crucial element in bricklaying that’s widely used in both construction as well as finishing works. Generally, they’re used to aerate concrete blocks, connect bricks, prepare plaster, floor levelling as well as the making of precast products. The major reason cement is one of the most common construction materials as its incredible ability to hold structure together. To get a cement plaster, you’d simply have to mix cement with both water and sand. However, when you mix cement with lime, sand and water, you’ll get a mortar.

For cements mortars to be used inside joints, you’ll have to include 1 part cement at the minimum to not more than 2 parts sand by weight which should be dry mixed and moistened with enough water to allow for troweling and packing without falling apart. Generally, the cement sand ratio in a mortar is in between 1:2 to 1:6. The cement and sand mix ratio is largely based on the importance of the project.

Cement provides a plethora of uses in bricklaying and these includes:

• Preparation of cement concrete

• Preparation of cement mortar

• Building fireproof and thermal proof structures

• Building chemical proof structures

• Serving as a grout material

• Building hydrographic and frost resistant structures

• Manufacturing precast members

• Constructing aesthetic concrete

• Constructing cement concrete roads

There are several types of cements with each having its specific purpose. For instance, the type of cement more suited to building a fire proof structure is a high alumnia cement and to build a hydrographic structure, cements like expanding cement, hydrophobic cement, pozzolana cement and quick setting cement are the best bet. Acid resistant cements are more useful in building chemical proof structures, portland cements are best suited to making grout materials, while coloured cements are preferable to building aesthetic structures.

Some individuals who have been in the construction department for many years may not be qualified, that is, they may not have undergone an apprenticeship and/or trade certificate courses, but they might still be very skilled at their work. However, anybody can pick up a sledgehammer and demand themselves a builder lacking any skills or training. The wise thing would be to ask the builder coming to your house about what qualifications they have and what training they have undergone.

Licensing of building practitioners

You can now check if your builder or tradesperson is a licensed building practitioner by using an electronic public register which has a record of every registered builder. Being licensed provides you with an assurance that the builder who is about to do your work has proven his shill to the government and earned his right to be a practitioner. If you wish for certain important building and design work on your home it is imperative that you hire a licensed practitioner, the act is very common when you compare the scenario with when you have to call a plumber or an electrician regarding any work.

In order to become a builder in the UK, you must complete an apprenticeship or an NVQ. NVQ is another popular route to becoming a builder. You can also get your NVQ even when you are working as an apprentice. You can also make it based on any recognised overseas qualification.

All associates maintain a Code of Practice and Conduct which sets the standards for all stages of the building procedure. The Code requires builders to:

• Submit quotes on projects for which they have time.

• Securing the contract with a sufficient insurance cover.

• Maintain honesty and integrity at all times.

• Obey the law and industry standards of conduct.

All members of the construction association must also follow a code of conduct. As a consumer, if you think your builder has breached the Code of Conduct or the Code of Ethics, you can file a written against him or her.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.