Find a Builder you can trust near you.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

What Is Plasterboard?

The plasterboard is unarguably one of the most common building materials across the globe. Sometimes referred to as gypsum board, gyprock, drywall or wall board, the plasterboard is mostly incorporated for ceiling cladding and interior walls in several homes and offices in recent times. However, despite its global acceptability, it’s a very misunderstood building material.

The plasterboard is manufactured using a gypsum core with a heavy paper covering both sides of the sheet. The measurement of a standard plasterboard sheet is a length of 2.4 metres in and a width of 1.2 metres, with a thickness of about 13mm. The board usually have either a bevelled or a bit flat edge. The bevelled edge makes it easy for the installers to use a plaster to smooth out the surface after nailing the sheets to walls and ceilings as well as taping the edges.

The plasterboard comes in different types. Although various manufacturers provide a unique name for their products, but they’re all included in one of the following categories:

• Water Resistant Plasterboard - This type of plasterboard are best suited to be used in water areas like bathroom, laundry rooms and kitchens.

• Acoustic Plasterboard - Due to its sounding proofing qualities, this type of plasterboard is preferred to be used in home theatres or noisy areas.

• Flexible Plasterboard - This is to be incorporated on curvy surfaces.

• Fire Resistant Plasterboard - Just like the name implies, this type of plasterboard is best suited for use in high fire hazard areas.

If you’re about to kick start some small renovations around your house or office, using a plasterboard to clad your walls is a very simple and worthwhile task. However, if you want to do major renovations or need to apply plasterboard to your ceiling, the best option would be to leave it to a seasoned professional.

Damp issues on a property are usually generated by a lot of factors such as a poor or broken guttering, condensation and lots more. The question arising here is what is the possibility of External Wall Insulation (EWI) preventing condensation? Not only is EWI a reliable way to reduce condensation-caused damp, but it’s also one of the major reasons property owners in solid wall homes consider thermally rendering or cladding their external walls.

Condensation arises as a result of warm moist internal air hitting a cold surface such as the steaming up of both windows and mirror when having a shower. What happens here is the condensation of the water vapour in the air from a gas to liquid in the process of touching the cold surface - one whose temperature is significantly reduced to reach the dew point. At the dew point, condensation is very rampant, and to tackle this issue you’ll have to heighten the wall temperature in order to convert the moisture to vapour and permit it to pass through the wall. And that’s exactly the job of an external wall insulation!

To get started you must ensure that the walls are clean and dry prior to fitting the external wall insulation. The month of May through to September when the weather tends to be dry and more stable are usually the best period to carry out the project. The external wall insulation will function just like a cosy blanket around the building. Ultimately, changing the feel and temperature of the inside of your home. As a result, the previously cold walls will no longer be cold which goes a long way to mitigate the effects of condensation. Furthermore, when an EWI is installed, the rooms of your home will automatically trap more thermal mass as the heat is saved in the walls’ fabric and released back when the temperature drops.

In the event whereby you’ve got big refurbishment ideas for your house but a small budget, then you know it’s time to be a bit more creative and apply some cheap and simple tricks. The best possible way to go about this is to invest time in acquiring new skills rather than trying to save up more money to pay a pro to deliver the results you want. After all, the most significant cost when it comes to house refurbishments is usually the labour cost.

The key to making cheap tricks a lot effective in the refurbishment process is by undertaking small tasks that’ll make a huge impact. A great way to start would be by taking it one task at a time rather than rushing to complete all at once. This way, you’ll have enough time to perfect your skills before moving on to the next.

✓ Paint the interior walls. Although this is a simple task but it’ll save you a lot of money if done as a DIY project. To get started, you’d have to text colour options by painting samplex on the wall first. Once done, you can go for the one that adds warmth, dynamism as well as energy to the room.

✓ Fix up your furniture. This involves re-upholstering and refinishing any piece of furniture that appears tired or overly worn (you can leave out the ones that you do not really like or unnecessary items).

✓ Spruce up small but important items used on a daily basis. This includes spray-painting inexpensive picture frames, recovering lampshades with a vibrant paper or patterned fabric, adding throw pillows to armchairs and couches and the likes.

✓ Fix all small things that are broken. This includes activities like patching the nail holes in the wall, repairing the latch on the kitchen cabinet, fixing the gutter, putting a new handle on the door and lots more.

If you’re having issues with the amount of space in your home and need an extra space without affecting your garden, loft conversion comes to mind. Not only is it a great solution to creating more living space within a home, but it’s also one of the most budget-friendly solutions you can count on to expand your space by thinking upwards rather than sideways. So if you’re thinking about converting your loft, one thing that almost immediately comes to mind is whether or not your house is suitable for loft conversion.

To answer the question of whether every house can have a loft conversion is a very simple one. Generally, not every house is suitable for loft conversion. This is due to the fact that each and every loft space - from the stairways below and floors to the rafters and the roof up above, is unique. Therefore, the best way to really figure out whether or not a house’s loft offers the potential for conversion is to get in touch with a loft specialist.

So what can make a house not suitable for a loft conversion? Let’s take a closer look!

✓ A house will not be suitable for a loft conversion if the height of the ceiling happens to be too low and it’ll not be possible to have it raised.

✓ If you do not own own the freehold to the loft space, you won’t be able to convert the loft. Surprisingly, this happens to be a common issue in London.

✓ You will not be able to convert your loft if you reside in a conservation area or in a listed building. But you can identify a design solution that’ll still comply with the conservation rules and keep planners happy.

Are you looking to create some more space in your home with your garage being almost dispensable? If yes, then considering a garage conversion project may be the way to go. Unlike many other extension options, garage conversion does not take up an additional space as it only changes the current structure of the garage. As a result, the cost of completing a garage conversion project can be relatively attractive when compared to other space creating alternatives. So exactly how much would a garage conversion project cost? Well, there’s no precise answer for this as several influencing factors come to play. However, in this guide we’ll give you a rough idea of the average costs that you’re likely going to encounter. Some of the factors that can influence your budget dramatically includes the following:

• The size of the conversion. The larger the size of the garage per square feet, the more cost you’ll have to expend.

• The type of your property - listed buildings are usually more expensive.

• Your location in the UK. If you stay in London where there’s a higher demand, you’ll most likely pay more.

• You’re likely to pay more if a specialist knowledge is required.

• The amount of glazing to be installed

• Quality of the materials to be incorporated.

• Quality of the professional to carry out the installation service.

On average, when it comes to garage conversion projects, you’re likely to pay the following depending on the per square metre given:

• A single garage of about 15 square metre will cost within the range of £6,000 to £15,000.

• A double garage of about 30 square metre will cost within the range of £12,000 to £30,000.

Rendering of a house is one of those projects that can greatly improve the visual appeal of your home, enhance it’s energy efficiency, protect the brickwork from the elements and ultimately, add value to your home. Generally, the cost of rendering a house normally costs within the range of £25 to £70 per metre square, while the average cost house rendering costs stands at about £40 per square metre. Therefore, a 3 bedroom semi detached house will cost within the range of £4000 to about £5000.

The total cost of rendering a house is determined by a wide range of factors. These factors includes the following:

✓ Type of the rendering. There are three main types of rendering which includes sand and cement rendering, monocouche rendering as well as acrylic or silicone rendering. However, re-rendering applies to sand and cement sooner and it’ll also have to be painted every 3 to 6 years. Consequently, longer term cost can be higher when compared to the other types.

✓ Ease of access. Where your contractor will have to work around obstacles like shrubs or conservatory, this can make the cost a bit higher as it’ll take longer time to complete.

✓ Prep work. If the contractor needs to fill some cracks or perhaps an old mortar requires tuck pointing before rendering can be started, this will also affect the cost.

✓ Scaffolding. In the event whereby the job requires the use of scaffolding and you’ll have to hire one as a different cost, then the price will be higher.

✓ Your location. Due to the high standards of living and higher demands in areas like London or the Southeast, prices in these regions are usually higher than that of the other regions like Midlands and North.

Being a strong and durable product requiring little maintenance and expected to last over 2 decades, it’s little wonder resin is now a popular material amongst homeowners in the UK to build their driveways. However, there’s always the issue of the driveway fading, cracking or even becoming worn and tired. So is it possible to repair resin driveways? The answer is yes, a resin driveway can be repaired, however the best approach to use largely depends on the issue being faced. As a confident DIYer it’ll be very easy to do, but if you lack the confidence then calling in a professional for help would be a better option. So let’s take a look at how you can repair your resin driveways.

For cracks, the best reparation approach would be to chisel it out. Once done, then you can proceed to breaking the stones to form a rough edge. It’s important to make sure that the matrix of the stone remains unaffected. Make a new mixture of resin bound stone and pack it in tightly to the gap. While doing this, we’ll recommend making use of a plastic trowel to avoid burnishing. This fresh mixture will then create a smooth and perfect surface by interlocking with the edges. You can follow similar procedure for patches but these are larger holes or damages than cracks and as the name suggests are mostly likely to remain noticeable but will prevent further crumbling of your resin driveway.

For homeowners, who aren’t so keen about the patch repairs, you can opt for an overlay especially in the event whereby the majority of the surface has failed. Although many usually shy away from this approach because of the perceived high expenses, but the fact is that the approach is actually cost effective as you won’t have the need to spend more money in the long run.