Find a Builder you can trust near you.

Yes, bricklayers can work during the cold months, but it all depends on the type of work involved. For instance, residential housing maintenance works such as tuck pointing deficient mortar joints on exterior walls and columns as well as rebuilding of chimneys are best tackled during summer or simply put, the warmer months of the year. This is is mainly because the best results for these activities are achieved in the warmer months and several bricklayers will agree to this fact.

Mixing of mortar using anti-freeze technique to counter-act the effects of a cold weather can lead to white marks trailing down the brick when warmer temperatures comes knocking. As a result, even mortar mixing should be done at temperatures exceeding zero degree farenheit which will hold no serious consequences if the temperature should change to a little bit below the norms. During the winter, a good technique that can be incorporated to when mixing mortar would be to mix them in smaller quantities in a warmer environment. These small quantities will immediately be fed by the labourers to the bricklayers and in such circumstances, the mixed mortars will not be subjected to a freezing temperature for too long.

Generally, it would be very unwise to consider any bricklaying work to be done whenever the temperature jumps to a certain level which would be considered to be very inconvenient to work in. Interior works like remodelling of fireplaces can be tackled so long there is a warm space to mix the mortars while also keeping the materials at an indoor temperature. Bricklaying works that have, however, been completed during the colder months should be subjected to a very close inspection as well as looking for potential damage that can be caused to existing works as a result of the harsh weather.

The main reason that people use cladding or rendering on their property is the aesthetic benefit. These materials can really boost the appearance of a home. Cladding and rendering can also increase the thermal performance of a property. Speak to a specialist to find out whether your property will benefit.

Generally, it’s possible to extend a barn conversion, but there are certain conditions that you’ll probably need to meet. Ultimately, it’s up to your local planning office to decide whether to approve your planned barn conversion extension or not.

Typically, small extensions on the side of a barn conversion are often approved, particularly if they serve to preserve the original character of the barn. This could be because the extension will mimic the appearance of the original structure, or house facilities that would look odd in the original building.

However, you probably won’t be allowed to build a larger extension, or one that isn’t in keeping with the appearance of the original barn.

Cladding comes in a range of styles, such as flush, shiplap, and featheredge. Many types of cladding are also available in a variety of colours to suit any property. A cladding specialist will be able to discuss what solution is best for your property and how it works.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.

The best type of insulation for your property will depend on the type of walls and any insulation that’s already present. It’s usually a good idea to have some form of wall insulation as well as loft insulation, as this helps to prevent heat loss in both areas.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

How To Put Up Plasterboard

Putting up a plasterboard is a vital process when it comes to home renovations. However as daunting as it may seem, with a good guide and regular practice you can master the skill within a small period of time. If you lack proper training and experience, we’d recommend you hire a seasoned professional plasterer for help so as to get the best result and also avoid additional costs due to possible damages.

Putting up plasterboard is way quicker than wet plastering and also significantly reduces the drying time that can slow down your renovation plans. With a plasterboard, you can delve straight into the decorating stage and achieve a smooth finish. Below are the steps required to put up a plasterboard.

• The first step is cutting the plasterboard to shape which be one of the most challenging parts of the process. This is because you’ll need to fit the board around things such as plug sockets and window sills. As a result, this involves cutting complex shapes rather than just a simple straight line. To get this done, simply mark out the cut required with the use of a tape measure, combination square and spirit level for a better precision. Once done, you can then use a plasterboard pad saw to cut along the marked spots.

• After you made the required cuts, the next step is putting up the plasterboard. And depending on where the boards are going to be put, this could be a very challenging task. If you’re going to put the boards on the ceiling or somewhere very high up, you’d probably need an extra pair of hands for help. To get this done, use the appropriate screws to secure the boards in place if you’re installing them directly on studs. However, if you’d be fixing them onto bricks or blocks, a drywall adhesive is your best bet.