Gas Boiler (Repair & Servicing) in Wantage

How To Fix A Boiler

A boiler is subjected to regular usage, working for a several hours a day and providing hot water for shower on a daily basis and even more so during winter. With it’s power and efficiency, we tend to postpone or even totally overlook its maintenance. However, no matter how good your boiler is, it consists of many moving components and it’ll certainly develop some faults some day. When the inevitable occurs, you might want to save some money and get it fixed all by yourself.

When it comes to fixing boilers, seeking help from a licensed heating engineer is usually the best solution, however at times you might be just lucky to be faced with minor issues which you should be able to handle yourself. In this article, we’ll look at some of the most common causes of a broken boiler and how you can get your heating system up and running again. Let’s have a look!

✓ Low system pressure. In the event whereby your boiler display a low system pressure, it could mean that the system is about to breakdown. You’ll have to carry out regular inspections on the pressure gauge to see if there’s any noticeable changes and call in a heating engineer immediately to prevent a system breakdown from happening.

✓ Poor heat production. Although this is unlikely to lead to any great issues, but it’ll reduce the effective functioning of your heating system. To prevent a debris build, it’s important to have your boiler cleaned regularly.

✓ Strange noises. Boilers often make noises, so there’s nothing to worry about unless it’s a banging or whistling noise that’s very odd , then there may be a serious issue. You’ll have to check the air intake, pressure, exhaust and piping to ensure they’re working just fine, if not there may be a need for replacement.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

During a boiler service, your boiler engineer will perform a series of checks to ensure that your boiler is safe and efficient. First, they will conduct a visual inspection to check for any corrosion or leaks. They will also check the flame in your boiler. They’ll then remove the boiler casing and check all the components, including the heat exchanger, burner and spark probe, then clean the inside. After this, they’ll check the flue for obstructions and ensure that it’s safely fitted. They will then do a gas pressure check to ensure the boiler is working at the right pressure, before firing it up to check for any working faults.