Floor Tiling in Chipping Campden

Kitchen floor tiles are a very popular choice for several reasons. They’re durable, visually appealing, resistant to moisture and stain and also relatively easy to maintain and install especially when compare to wall tiles. This is a task that can be done by any competent DIYer but requires a lot of patience as well as confidence. If you lack these attributes, then we’d recommend that you hire a professional floor tiler who can guarantee the best results the first time. In this article we’ll take you through the kitchen floor tiling process. Let’s get started!

• Prepare The Subfloor

✓ Ensure the subfloor is very secure to support both the tile and the people working across it.

✓ If necessary, you can strengthen the kitchen floor with the help of a vinyl, heavy felt or any other good backer board.

✓ After successfully securing the floor, proceed to clear out all dust and dirt.

• Mix The Mortar

✓ Mix a thinset mortar be referring to the instructions on the package. ( Mix only the quantity you can apply within 30 minutes).

✓ Once the mixture looks similar to the thickness of mayonnaise, allow it to rest for about 10 minutes before application.

• Apply The Mortar

✓ Apply a thin layer of mortar

✓ Do not cover extensive areas as the mortar can become very dry.

✓ Spread the mortar with a trowel in curved patterns to make it flat on the floor.

• Set The Tile

✓ Set down the tile slowly, apply a little pressure until its holds firmly to the surface. ( Apply a consistent amount of pressure throughout to ensure equal heights for all the tiles)

✓ Continue with the process until all full tiles are well positioned

• Cut The Tiles

✓ Once all the full tile pieces are in place, start cutting to cover the edges requiring smaller tile pieces.

✓ Take accurate measurements of the outer edges needing smaller tile pieces.

✓ Cut the tile pieces to fit the measurement taken with the help of a wet saw or hand tile cutter.

• Grouting

✓ Remove all spacers and mortar residues and lay the grout

✓ Apply the grout along the tiles’ seams with a grout float

✓ Clean out excess grout with a damp sponge after leaving it to dry for about 30 minutes

✓ Once the grout is fully dried, apply the sealer (the drying process normally takes within 3 to 4 days).

Laying of floor tiles may seem seem to be a very tricky task that’s beyond the abilities of some homeowners, but in reality, it’s a task that most DIYers can handle - as long you don’t rush the process. With a little patience here and there, you’ll be amazed with how far you can go. The materials are quite easy to work with and tools, only requiring a little practice to master. However, if you don’t have the necessary confidence to pull this off, we’d strongly recommend that you call in a professional who can guarantee the best results for help. In this guide, we’ll walk you through the process of laying floor tiles.

• Floor Preparation

✓ The first step is to prepare the floor by moving all objects like mortar, adhesives and more.

✓ Use concrete patching compound to fill ill low spots and cracks, until the floor is levelled.

✓ Ensure the floor is dry and clean.

• Pattern Layout

✓ Take the measurement of each wall’s length while also taking into account the room’s diagonals.

✓ To help place the tiles in an orderly manner, make use of a chalk to mark down lines on the levelled surface in question and ensure it’s parallel to the walls.

• Adhesive Preparation

✓ Mix the appropriate amount of water with the adhesive (bonding agent).

✓ The mixture should be toothpaste-like thick to ensure the durability of the tiles.

• Tiles Placement

✓ Depending on the tile’s size, evenly spread the mortar on the floor using a notched trowel.

✓ Lay the first tile on the bonding agent (adhesive or mortar) and apply a gentle and little pressure on the tile.

✓ Repeat the technique for other tiles using plastic spacers to ensure the edges and corners are properly aligned.

• Tiles Cutting

✓ Cut the tiles (if necessary) with the help of a wet saw or scoring cutter featuring a diamond-tripped blade.

• Grout Application

✓ Filling of the tiles’ gap is done using the grout. It can be applied to the joints with a rubber float.

✓ After application, allow the grout to set up for some minutes.

✓ Use sponge and a bucket of water to clear out any adhesive leftover.

• Grout Sealing

✓ Use a foam brush or applicator bottle for the sealants’ application.

✓ Clean out excess sealer within 10 minutes.

Are you looking to tile your bathroom floor very soon? Well, we’ve got you covered! Tiling is not the easiest skill to acquire and definitely not one you’d not want to try out on your bathroom with some practices. For the best results and to get it right the first time, we’d recommend you hire the services of a reliable professional especially if you’re inexperienced or without a bathroom tiling training. Hopefully, this quick step-by-step guide will put you in the right direction.

Bathroom Floor Tiling Procedures

• Make Sure You Have A Levelled Subfloor

✓ Your subfloor’s stability is crucial for the success of your tile laying.

✓ Once done, then you can start planning how to level the floor.

✓ Identify the highest point of your floor and place a really long level to determine the dip and hump spots.

✓ Fill in the identified low spots with mortar.

• Cut The Tiles

✓ Using a wet saw with a diamond blade and pump, cut through the tiles to get the appropriate shape.

• Choose The Appropriate Adhesive

✓ To best adhesive is probably the one written on the label and suggested by the manufacturer.

✓ If uncertain, you can make use of a modified mortar

• Prepare The Area

✓ Using the prepared mixture of your mortar, prime the surface by spreading it on the floor with the trowel’s flat side.

✓ Once done, you can add more mortar with the ridges of the trowel.

• Space The Tiles

✓ Tile spacement depends largely on the surrounding walls. Straight walls equal straight tiles, if not your judge would be required to ensure a great outcome.

✓ If the wall is straight, make a space of about an eighth of an inch. The bigger spacing, the higher the possibility for the grout to become visibly discoloured.

• Use The Right Grout

✓ With sanded and unsanded grouts having a variety of colours, choosing the ideal grout can a tricky affair.

✓ The size of the spaces play a huge role in determining the best choice.

✓ Use a sanded grout if the spacing is an eighth of an inch or more. However if less, make use of the unsanded grout.

Have you laid your tile and left it to set? If yes, then the next step is to start grouting. Before you get started there’s a need to make ready the right grout for the type of your grout as well as background material. If you’re not certain of the right grout you can reach out to the grout manufacturer for help. Grouting of floor tiles is not the easiest and tasks and should be left to a reputable professional in order to avoid costly mistakes and unnecessary costs. In this post, we’re going to take you through the processes involved in grouting of floor tiles in order to put you on the right track. Let’s take a look!

1. Depending on the adhesive used to lay your tiles, make sure you leave enough time for the tiles to fully set.
2. Get a mixing bucket and mix grout powder and water as instructed on the packaging. Ensure not to make too much as this will make it solidify quickly and unstable.
3. Apply some grout on the tiles - hold the grout float at 45 degree angle and apply the grout to fill all of the joints.
4. Once you’re done grouting all of the joints between the tiles, leave it for up to 10 to 15 minutes to dry before wiping down the tile surface using a damp sponge. Ensure not to apply too much pressure on the grout joints.
5. Let the tiles rest for about an hour so as to allow the grout solidify and harden a bit more. Once done, proceed to take off the excess grout and smooth it off.
6. Wipe down the tiles until they’re totally clean using a clean cloth.