Floor Tiling in Dunbar

Laying of floor tiles may seem seem to be a very tricky task that’s beyond the abilities of some homeowners, but in reality, it’s a task that most DIYers can handle - as long you don’t rush the process. With a little patience here and there, you’ll be amazed with how far you can go. The materials are quite easy to work with and tools, only requiring a little practice to master. However, if you don’t have the necessary confidence to pull this off, we’d strongly recommend that you call in a professional who can guarantee the best results for help. In this guide, we’ll walk you through the process of laying floor tiles.

• Floor Preparation

✓ The first step is to prepare the floor by moving all objects like mortar, adhesives and more.

✓ Use concrete patching compound to fill ill low spots and cracks, until the floor is levelled.

✓ Ensure the floor is dry and clean.

• Pattern Layout

✓ Take the measurement of each wall’s length while also taking into account the room’s diagonals.

✓ To help place the tiles in an orderly manner, make use of a chalk to mark down lines on the levelled surface in question and ensure it’s parallel to the walls.

• Adhesive Preparation

✓ Mix the appropriate amount of water with the adhesive (bonding agent).

✓ The mixture should be toothpaste-like thick to ensure the durability of the tiles.

• Tiles Placement

✓ Depending on the tile’s size, evenly spread the mortar on the floor using a notched trowel.

✓ Lay the first tile on the bonding agent (adhesive or mortar) and apply a gentle and little pressure on the tile.

✓ Repeat the technique for other tiles using plastic spacers to ensure the edges and corners are properly aligned.

• Tiles Cutting

✓ Cut the tiles (if necessary) with the help of a wet saw or scoring cutter featuring a diamond-tripped blade.

• Grout Application

✓ Filling of the tiles’ gap is done using the grout. It can be applied to the joints with a rubber float.

✓ After application, allow the grout to set up for some minutes.

✓ Use sponge and a bucket of water to clear out any adhesive leftover.

• Grout Sealing

✓ Use a foam brush or applicator bottle for the sealants’ application.

✓ Clean out excess sealer within 10 minutes.

Kitchen floor tiles are a very popular choice for several reasons. They’re durable, visually appealing, resistant to moisture and stain and also relatively easy to maintain and install especially when compare to wall tiles. This is a task that can be done by any competent DIYer but requires a lot of patience as well as confidence. If you lack these attributes, then we’d recommend that you hire a professional floor tiler who can guarantee the best results the first time. In this article we’ll take you through the kitchen floor tiling process. Let’s get started!

• Prepare The Subfloor

✓ Ensure the subfloor is very secure to support both the tile and the people working across it.

✓ If necessary, you can strengthen the kitchen floor with the help of a vinyl, heavy felt or any other good backer board.

✓ After successfully securing the floor, proceed to clear out all dust and dirt.

• Mix The Mortar

✓ Mix a thinset mortar be referring to the instructions on the package. ( Mix only the quantity you can apply within 30 minutes).

✓ Once the mixture looks similar to the thickness of mayonnaise, allow it to rest for about 10 minutes before application.

• Apply The Mortar

✓ Apply a thin layer of mortar

✓ Do not cover extensive areas as the mortar can become very dry.

✓ Spread the mortar with a trowel in curved patterns to make it flat on the floor.

• Set The Tile

✓ Set down the tile slowly, apply a little pressure until its holds firmly to the surface. ( Apply a consistent amount of pressure throughout to ensure equal heights for all the tiles)

✓ Continue with the process until all full tiles are well positioned

• Cut The Tiles

✓ Once all the full tile pieces are in place, start cutting to cover the edges requiring smaller tile pieces.

✓ Take accurate measurements of the outer edges needing smaller tile pieces.

✓ Cut the tile pieces to fit the measurement taken with the help of a wet saw or hand tile cutter.

• Grouting

✓ Remove all spacers and mortar residues and lay the grout

✓ Apply the grout along the tiles’ seams with a grout float

✓ Clean out excess grout with a damp sponge after leaving it to dry for about 30 minutes

✓ Once the grout is fully dried, apply the sealer (the drying process normally takes within 3 to 4 days).

Due to its numerous advantages, bathroom floor tiles are a popular choice for homeowners across the country. Not only are they durable and good looking, but they’re also resistant to both moisture and stains. Hence, they’re very easy to maintain and with skill, confidence and patience, can also be relatively easy to install especially when compared to wall tiles which is a vertical surface.

Fitting bathroom floor tiles requires a lot of planning as it can be easy to make costly errors here and there. Generally, this task shouldn’t pose any serious difficulty for a confident and patient DIYer. However, if you lack these attributes, then it’s advisable to call in a professional who can guarantee the best results for help. In this article, we’ll take you through the bathroom floor tiles installation process. Let’s get started!

• Make Sure You Have A Levelled Subfloor

✓ Your subfloor’s stability is crucial for the success of your tile laying.

✓ Once done, then you can start planning how to level the floor.

✓ Identify the highest point of your floor and place a really long level to determine the dip and hump spots.

✓ Fill in the identified low spots with mortar.

• Cut The Tiles

✓ Using a wet saw with a diamond blade and pump, cut through the tiles to get the appropriate shape.

• Choose The Appropriate Adhesive

✓ To best adhesive is probably the one written on the label and suggested by the manufacturer.

✓ If uncertain, you can make use of a modified mortar

• Prepare The Area

✓ Using the prepared mixture of your mortar, prime the surface by spreading it on the floor with the trowel’s flat side.

✓ Once done, you can add more mortar with the ridges of the trowel.

• Space The Tiles

✓ Tile spacement depends largely on the surrounding walls. Straight walls equal straight tiles, if not your judge would be required to ensure a great outcome.

✓ If the wall is straight, make a space of about an eighth of an inch. The bigger spacing, the higher the possibility for the grout to become visibly discoloured.

• Use The Right Grout

✓ With sanded and unsanded grouts having a variety of colours, choosing the ideal grout can a tricky affair.

✓ The size of the spaces play a huge role in determining the best choice.

✓ Use a sanded grout if the spacing is an eighth of an inch or more. However if less, make use of the unsanded grout.

If you’re considering the installation of large format porcelain tiles in your home or property, you’d probably want to know how you can go about the laying process. Large porcelain tiles can measure up to 3m in length and as a result, requires specialist skills, equipment as well as products in order to see to a high quality installation of the tiles. In this guide, we share with you expert tips that’ll help install large porcelain tiles onto floor space with relative ease. Let’s take a look!

✓ Prepare the tiles. This includes cleaning the surface of the tile of any dirt, dust and removing any temporary protective layers. This is because any contamination to the tile’s surface can affect the suction action of the lifting frame.

✓ Cut your porcelain tiles. For cutting, the tiles should be transferred to a stable base for for more accuracy and clean cut. Use the measurements to get a perfect cut and if you’ll require a straight cut simply use the score and snap tools and techniques.

✓ Prepare the adhesive. Follow the manufacturer’s instructions to prepare the adhesive.

✓ Install the large porcelain tiles. Use a 4mm notched trowel to backcomb the adhesive onto the tile’s reverse. All ribs should run in same direction and also be parallel with the shortest length. Use a larger notched trowel to apply the adhesive to the substrate. Once you’ve applied the adhesive to both surfaces, you can then life the tiles into place with the lifting frame. Then use the tile levelers to ensure the tiles are flush at the joints and wipe off any excess adhesive

✓ Apply the grout.