Floor Tiles (Supplied and Fitted) in Port Talbot

How To Lay Tiles On Concrete

Installation of tiles on concrete sub-floors can be done with relative ease under adequate guidance. Here is what you have to do.

lPrepare The Concrete Subfloor

• Ensure the concrete is dry, clean and must be at least 6 weeks old.

• If there are dips and humps, level the concrete using a levelling compound.

lSet Out

• Working from the centre outwards, take a measurement of the floor (both length and width) and draw a cross at the centre.

• Lay out the tiles from the cross with a space of 3mm between each tiles. This will allow for movement stresses within the floor and later to be filled with grout upon installation of the tiles and adhesive dried.

lCut The Tiles

• Due to the particularly had nature of some floor tiles such as natural stone and porceclain, high quality tools are usually required to produce a clean cut through the tiles. With the help of an electric wet cutter alongside a slide cutter and nippers, your job would be made a lot easier.

• For a better result during intricate cuts, make use of a cardboard template.

lFix The Tiles

• The tiles should be fixed using a cement-based adhesive.

• Ensure to refer to the packaging or product data for the mixing ratios information.

• Stir the mixture till its lump-free

lApply The Mixture

• Spread the mixture onto the concrete sub-floor to create parallel ribs with the help of a floor trowel.

• Push the tiles into the parallel ribs.

• Clear out any excess adhesive from the tiles surface with a damp sponge.

• Do not walk on the tiles for at least 2 hours.

lGrout

• Once the adhesive is dried, wipe out any dust, adhesive or dirt from the tiles’ gaps.

• Mix about 4 to 5 parts of grout powder with 1 part of water and ix together.

• Apply the mixed grout diagonally across the tiles using a soft rubber grout float.

• Wipe out excess grout from the tiles surface and allow the tiles to dry.

• Stubborn residues can be cleaned using any washing up detergent with warm water within 24 hours after grouting.

Are Floor Tiles Expensive?

Are you considering installing floor tiles in your home or office? Just like many other home and property owners, this is one of the many questions that first pops up. Floor tiles can add colour and texture to your living space and comes in various shapes and sizes. The cost of floor tiles depends on a wide range of factors such as the type of floor tiles as well as the quality. The cheapest of them all is the vinyl tiles which can be easily cut through and waterproof when properly sealed. As a result, making them a better fit for bathroom floors. Other kinds of tiles include ceramic tiles, mosaic tiles, quarry tiles and porcelain tiles. Each of the types have their own unique qualities including the quarry tiles’ durability and the afore-mentioned vinyl tiles’ waterproof qualities.

Having in mind that the major part of your floor tiles cost largely depends on the type selected, you can then go ahead to contact your preferred tiling professional for an installation only quote ( this can go a long way to help control the overall cost). The quote provided will, of course, be based on the room’s size as well as your preferred choice of tiles. The average price of bathroom floor tiles installation ranges about £20 to £25 per square metre. Meanwhile for a kitchen floor tiling project of about 8 square metres in size, the cost should range between £500 to £600 ( this quote includes both installation cost and all the materials included).

Finding a tiling professional you can rely on to complete your project and delivery a top quality job while also offering a very competitive price can be almost impossible. The professional you use greatly determines the price of your floor tiling effort, so there’s the need to review various professionals before making a decision.

Removing floor tile is always a simple task until you get started. Then, you’d realize not only is it a tedious and time consuming task, but also one with multiple hidden challenges that’s only revealed once the project is underway. If you have no experience or perhaps you lack the confidence required to pull this off, we’d highly recommend you call in a professional who can guarantee the best outcome and save you some unnecessary spending. However, if you wish to tackle this yourself, this guide would be your perfect partner to ensure a successful outcome.

To get started, you’ll need the following tools; hammer, chisel, pry bar, scraper, trash can as well as a broom or shop vac.

1. Remove fixtures. Ensure the room is empty and remove all fixture that may get in the way.
2. Pick a starting point. Use a hammer and chisel to chip out a tile and create a starting point for the task. Depending on how the tile is affixed and the underlayment type incorporated, the tile may remove easily or require some effort. Use a hammer, chisel, pry bar or pole scraper to remove the tiles.
3. Remove the tiles. From the starting point created, proceed to pry up the tiles. Deposit then in a trash can or large bucket in order to reduce clutter.
4. Access underlayment. There are cases whereby the tiling is attached directly to a concrete floor or subfloor, however the common practice is having a plywood or mortarboard underlayment. The damaged underlayment should be detached to expose the subfloor.
5. Clear debris. Wipe out all debris from the floor using a broom or shop vac.
6. Remove nails. If you removed the damaged underlayment, you may have to either remove or pound in some nails to get a level surface.

Are you looking to tile your bathroom floor very soon? Well, we’ve got you covered! Tiling is not the easiest skill to acquire and definitely not one you’d want to try out on your bathroom without some practices.  For the best results and to get it right the first time, we’d recommend you hire the services of a reliable professional especially if you’re inexperienced or without a bathroom tiling training. Hopefully, this quick step-by-step guide will put you in the right direction.

1. Make Sure You Have A Levelled Subfloor
   Your subfloor’s stability is crucial for the success of your tile laying.
2. Once done, then you can start planning how to level the floor.
3. Identify the highest point of your floor and place a really long level to determine the dip and hump spots.
4. Fill in the identified low spots with mortar.
5. Cut The Tiles
6. Using a wet saw with a diamond blade and pump, cut through the tiles to get the appropriate shape.
7. Choose The Appropriate Adhesive
8. To best adhesive is probably the one written on the label and suggested by the manufacturer. If uncertain, you can make use of a modified mortar
9. Prepare The Area
10. Using the prepared mixture of your mortar, prime the surface by spreading it on the floor with the trowel’s flat side.
11. Once done, you can add more mortar with the ridges of the trowel.
12. Space The Tiles
    Tile spacement depends largely on the surrounding walls. Straight walls equal straight tiles, if not your judge would be required to ensure a great outcome.
13. If the wall is straight, make a space of about an eighth of an inch. The bigger spacing, the higher the possibility for the grout to become visibly discoloured.
14. Use The Right Grout
15. With sanded and unsanded grouts having a variety of colours, choosing the ideal grout can a tricky affair.
16. The size of the spaces play a huge role in determining the best choice.
17. Use a sanded grout if the spacing is an eighth of an inch or more. However if less, make use of the unsanded grout.