Oil Boiler (Repairs or Servicing) in Dalmally

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How Long Does It Take To Service An Oil Boiler?

Are you about to service your oil boiler and wondering just how long it would take to completion? Well, you should first know that during an oil boiler service, there are a wide range of things that needs to be checked. As a result, the service can actually take some time and even more, depending on the present condition of your oil boiler.

During a boiler service, your qualified heating engineer will carry out the following tasks:

• Detach and clean both the burner and fan.

• Examine the combustion chamber rope seal.

• Wipe clean and descale baffles.

• Wipe clean and descale the main heat exchanger

• Detach, clean and replace turbulators

• Examine the combustion levels after cleaning.

He’ll also perform some tank and system checks which includes:

• Inspecting and cleaning condensate

• Testing the fire valve

• Cleaning or replacing the filter

• Cleaning the condense trap

• Conducting a thorough inspection of the tank and oil supply pipe to identify possible damages, deterioration as well as debris.

• Pressure testing the oil supply pipe at the point where it goes underground.

• Examining the system pressure.

With all the aforementioned activities and more, an oil boiler service may take relatively longer period of time when compared to it’s counterpart - gas boiler. This is mainly due to the fact that the boiler itself requires a thorough inspection as well as the oil tank where the fuel is being stored. You get your gas through the mains supply, however oil must firstly be stored inside the tank then filled up when it’s almost low. The oil tank will be inspected to identify possible leaks, bulging, corrosion as well as water.

So generally, an oil boiler service should take between the range of 1 to 2 hours to be completed.

How Can I Get My Oil Boiler Repaired?

Did your oil boiler just broke down and you’re considering your repair options? Well, you’ve come to the right place! Whenever your oil boiler breaks down, you have two options - repair it yourself or get in touch with a reliable professional. If you lack proper training or experience when it comes to fixing of oil boilers, we’d recommend that you rather hire the services of a trustworthy oil boiler engineer who can guarantee the best results while also saving you time and money that could result from possible costly errors.

However the issue is, not all oil boiler repair services are created equal. The words “expert and “professional are now so cheap that almost, if not all oil boiler repair companies online today make use of those words to qualify themselves. However, when several of them are done delivering their oil boiler repair services you’ll have no other choice than to start questioning their claimed status. In order to separate the boys from the men very early on, a little caution and some research is all that’s needed to know the most reliable company to approach.

To get a good repair company, the first step would be to make sure the company is fully accredited with a professional certification scheme so as to be sure that they’re actually qualified to deliver the service.

Another step you can take is by requesting personal recommendations from family and friends. For a company to be referred by several homeowners in the local area then it must be doing something that’s worth the money invested.

You can as well make use of the internet to get a reliable oil boiler repair company. You can start by visiting the website of the company that manufactured you appliance to identify any recommended repair companies. Go through the companies’ testimonials but do not rely too much on them because in several cases they may not be authentic.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.