Roof replacement (Pitched/Tiled) in Bordon

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

One of the most popular choices for roofing materials are roof slates. There is a number of advantages that a roof slate has, hey can be aesthetically pleasing, they can also increase the potential selling value of the house and many more. Slate is a sturdy and resilient material that delivers waterproofing physical characteristics to a pitched roof. Unlike other roof materials which absorb water slates do not. Therefore, slate is the most resistant towards freezing and water damage.

Find out the pitch of your roof

Before beginning with the fitting procedure, you need to figure out the pitch of your roof. The roof pitch commands how much overlap is essential with each slate. This has been made a lot easier than the early days with the advancement of technology.

Find out the required overlap

Once you’ve found out the exact pitch of your roof accurately, take a look at the slate producer’s description. Each manufacturer will propose the obligatory overlap in order to form a firm and safe slate roof.

Roll out the roof membrane

Firstly, guarantee your joists or trusses are clean of any sheards or old nails that could harm the membrane. You will now have to roll the chosen roofing membrane along the roof trusses. It is always wise to start from one of the bottom corners and keep rolling it along to the other corner.

Secure the roof membrane

Once the membrane has been moved out, use thump nails to protect one edge. You will now have to pull the membrane taut and carefully fix it into position. Do this before adding any nails across the membrane at points of intersection with the trusses for extra stability.

Batten placement

This is done to find the proper assignment of the battens. For this, you will need two full-sized slates along with an under eaves slate. Carefully position the battens on the top of the roof on the top of the overlay. Make sure not to fix them down since it will be easier to move them around and make any adjustments.

An eave is the edge of a roof, which is why they are now and then called roof eaves. On a household's outside, eaves can stick out outside the side of the building, serving both ornamental and applied purposes. The eave of a house has come to mean the lower area of the roof that projects after the external covering, as opposite to a cornice, which is part of the entablature in Classical architecture.

Think of how a roof outspreads outside the covering, and then think about how a hard rain may roll down the roof and, on the ground, away from the structure. Centuries ago, the eavesdrop was that indentation line made around a structure when the rain fell off the edge of the roof onto the ground.

Types of Eaves

A roof can come to a conclusion in essentially three ways. A closed eave is the one which has very little or no overhang at all. An open eave has a visible overhang, projecting beyond the roof brackets. A boxed eave is surrounded with a soffit.

The Use of Eaves?

An eave can defend the siding and substance of a structure. A roof eave bulging beyond the sides permits snow and rain to fall from the roof away from the covering, to the ground. The more the "weather" gets thrown away from the household, the chances of you having a dry basement increases.

In cases of regions with a warmer climate, a large eave can help provide shade to the interior of the house. In rainy environments, the prolonged eaves of Asian architecture deliver shelter from the climate, as well as direction. In the 21st century, an eave may be an inconspicuous site for security cameras and light.

There is simply not one single answer when it comes to knowing how much would it cost to replace a commercial roof. Replacement costs is a variable which is dependent on several factors.

If you are looking to take a shot at guessing an estimate, you will first need to understand the what is need for the replacement.

YOUR COMMERCIAL ROOF IS AGEING

The first sign of replacement is definitely the age. Generally, roofs come with a warranty of twenty years. Based on your materials, the real lifespan for a commercial roof tends to be around 15 to 25 years. Depending on the maintenance and the materials, lifespan can be prolonged.

YOUR COMMERCIAL ROOF LOOKS TIRED

Compare your commercial property with other buildings in the area. If it looks pale and worn out in comparison, it is high time for replacement.

WATER DAMAGE

A sturdy roof should be able to withstand extreme weather conditions such as heavy rain or high winds. However, if a storm has caused significant damage to your roof, its structural integrity might be compromised. water damage is one of the most indicative signs for a roof replacement.

CRACKS AND HOLES IN ROOFING MATERIALS

Proper upkeep of the roofing materials is required for it to continue protecting your property. If you find any cracks or holes, bent tiles or sheets, replacing them is advisable.

SAGGING COMMERCIAL ROOF

Roof replacement is critical when your roof suffers from sagging or corrosion. Once sagging or corrosion begins, the structure becomes vulnerable to damage.

Keeping all the above factors in mind, replacing your commercial roof can range from anywhere around £10,900 to £44,000 depending on the materials you choose. Materials are available in the market from £35 to around £75 per square meter. If you chose higher or premium quality materials, price can range from £115 to £200 per square meter.