Fascias and soffits are a critical aspect of the majority of guttering systems. Not only do they provide support for the guttering itself, they improve the looks of your building by producing a clean and tidy finish to the roofline. Fascias or fascia boards are horizontal planks that sit on the edge of the rafters of your roof, closing the end of the roof and providing the support that the guttering is attached to. Soffits run beneath the fascia boards, closing the gap and protecting the underside of the rafter ends. Soffits are usually ventilated to enable the roofing timbers to breathe and to prevent any moisture buildup. Box ends are used where the horizontal fascia meets the diagonal barge board that runs up the edge of the roof profile, offering a neat finish to an otherwise ugly join.
Fascias and soffits are usually produced from either wood or UPVC. Timber fascias and soffits are typical on older properties and remain popular. However, timber fascias and soffits can rot with time and expose the rest of the guttering to issues or leaks. Recently, UPVC fascias and soffits have been increasingly popular as they provide a durable substitute that won't rot. UPVC fascias and soffits are available in a number of colours to match any house, although white is extremely popular as it offers a traditional appearance. Fascias are also available in ogee moulded designs, where feature grooves are incorporated. These can have a striking effect.
In the South West, a typical job costs about £2,200, with prices from around £850 for small jobs to £4,000 for bigger ones. Too few tradespeople covering Okehampton have set their prices yet, so these figures are for the South West.
| Avg. price low | Avg. price low |
|---|---|
| Avg. price | Avg. price |
| Avg. price high | Avg. price high |
£4100
£3075
£2050
£1025
£0
Searches that showed one of our pages for Okehampton, all services
Okehampton is a community as well as civil parish in West Devon in the English region of Devon. It is situated at the northern side of Dartmoor, and also had a population of 5,922 at the 2011 census. Two electoral wards are based in the community (east as well as west). Their joint population at the very same census is 7,500. Okehampton is 21 miles (33 km) west of Exeter, 26 miles (42 kilometres) north of Plymouth as well as 24 miles (38 km) south of Barnstaple.
2 rated pros are based within 25 miles of Okehampton. Pros with a recent written review are shown first, nearest and best rated first.
A business with customer satisfaction guaranteed, we aim to please with our workmanship, good reliable company. No job to big or small, All estimates free of charge.
Haven’t a quote yet
Crediton - EX17
Enquiry from: Tim O
Start Date: Immediate
Replace rotten wood with plastic i think
North Tawton, Okehampton - EX20
Enquiry from: Paddy B
Start Date: Immediate
Soffits and Fascias enquiry
North Tawton, Okehampton - EX20
Enquiry from: Steve T
Start Date: Immediate
Damage to first floor upvc front facia. Fracture and a hole that needs repair.Can send photos
Answer a few quick questions, so we can match you with local gutter installers who can help.
Get free, no-obligation local soffits and fascias quotes from 4 verified gutter installers working in Okehampton.
Compare customer reviews, services and prices, and choose the right tradesperson for you.
Very excellent service and tracesmen Very excellent service and recomended excelled tradesmen
Very good service.
Very quick Received a call with an offer to give me a quote very quickly. Very happy
Soffits are constructed by homeowners on their properties for several purposes. Not only are they incorporated to hide away the unsightly features of a home, but they can also be used to add decorative architectural detail. Soffits construction, on the other hand, is a project that can be done by any DIY person with the knowledge and experience. However, if you lack the confidence to pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the best results, the first time. In this guide, we’re are going to take you through the soffit construction process.
✓ Measure and mark. The first step is to take an accurate measurement of the size of your propose soffit and use a pencil to mark it out on both the wall and ceiling. The size of your soffits is mainly determined by your needs or preferences.
✓ Cut and Install Wall & Ceiling Plates. Proceed to cut the wall as well as ceiling plates once the dimensions have been marked. Make use of 2x4 lumber, you can cut to size with the help of a table saw or mitre. Once done, you can then attach it to the wall as well as ceiling studs with a framing nail gun.
✓ Build the box frame. Develop a box-frame from 2x4 lumber, using your measurements as guide.
✓ Fit the box frame. Hold the box frame in place with some slide clamps and then attach it to the ceiling and wall plates with drywall screws.
✓ Mark the studs. Make use of a pencil to mark out the studs location on your soffit box frame.
✓ Cut and hang the drywall. Cut the drywall with a utility knife uing your measurement as a guide. Once done, attach the drywall to the framework with the help of drywall screws.
✓ Add finishing touches. This includes installing the corner beads, finishing off with the common drywall work of taping, spackling and sanding. Once the spackle is dry, you can the complete it by painting the soffit.
In general uPVC is used for soffits and fascias as it is very strong and durable. It also requires very little maintenance. However, wood can be used and is still popular on listed properties as it retains the original material. Older and listed buildings may require more traditional materials to be used.
Every year, various parts of your roof may need to be changed at one point or the other. Due to the fact that this event can occur at any time in a year, there’s the need to be fully ready. When it comes that being ready, you simply can’t overlook the importance of soffit and fascia boards in protecting your roof space and helping it maintain its clean and unique visual appeal. As a result, when your soffit and fascia boards need to be changed, you best do so as quickly as possible.
This task can be completed by anyone with basic DIY knowledge and experience, but if you lack the confidence to pull off then it’ll be advisable to hire a professional who can guarantee the best results for help.
✓ Remove the old existing boards. In order to install the new soffit and fascia boards, you’d have to remove the existing ones first. If necessary, you can make use of a Stanley knife to make the process much easier.
✓ Fixing soffit boards. Several soffit boards are made using uPVC. The boards are to fixed to the underside of your timber rafter ends. Make sure to use timber to close any gaps between soffit boards and also make sure that your soffit boards’ back are resting against the wall’s top.
✓ Fixing fascia boards. Many fascia boards are also made from uPVC and are usually installed in a similar way to soffit boards. Use a minimum of two nails to make sure they’re secure enough to hold weight of any roof tiles and also to prevent any buckling.
✓ Guttering and felt. To start the guttering, you’d have to screw any brackets into the facia board. You can use a spirit levelto make sure the alignment is perfect to enable the floe of water directly through your guttering system. Once done, you should also check for any rotting roof felt at the edges closest to the gutterin. If there is a rot, make use of eaves felt trays and tuck under existing felt and overlap into the guttering
Soffits and fascias sit along the sides of your property, over the join between your walls and your roof. The fascia attaches to the end of your roof rafters, hiding and protecting them. The soffit fixes on the bottom of the fascia, bridging the gap between your fascia and wall. Your guttering attaches to the fascia, which also joins to the bargeboard on your gable end, if you have one.
We can help you get more soffits and fascias work with our qualified job leads and boost your business.
Join today