Find a Renewable Energy Specialist you can trust in Jarrow.

Air source heat pumps work by taking heat from the air and using it to heat your home. They absorb heat from the air into a fluid, which then goes to a compressor where it gets hotter. This heat is then used to warm up water or air, which is distributed around your home.

First and foremost, you should know that heat pump is simply a device whose primary function is the transmission of thermal energy from one spot to the other. A good example can be found in the refrigerators whereby the evaporation as well as cooling of a liquid is incorporated to lower the storage compartment’s temperature. In recent times, this whole technology is utilized to draw the potential thermal energy present in the air outside and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. This is exactly what an air source heat pump does as it absorbs heat from the air and convert it into a higher temperature using a compressor. How the air source heat pump works is really simple, it’s just like a refrigerator but in reverse. Let’s take a look!

• The air source heat pump extracts heat present in the outside air into a liquid refrigerant at a reduced temperature.
• The pump then compresses the liquid to increase its temperature with the help of electricity. Once done, it then compresses it back to liquid so as to free the heat stored.
• The heat released is then directed to the radiators or under floor heating, while the ones left would be stored in the hot water cylinder.
• The hot water that’s stored can be used for showers, baths as well as taps.

Overall, the air source heat pump is an efficient way to make your home warm. It makes use of electricity to function, but it should consume lower electrical energy than the heat it generates.

If you’re looking to install some new solar panels in your home or property, then you’d probably want to know how it works. This is one of the most frequent questions asked by homeowners when it comes to solar panels and in this article we aim to give you a good insight on the operations of solar panels. Let’s have a look!

Generally, solar panels work by absorbing the energy of the sun and then converting it into electricity. It functions by allowing photons from the rays of the sun release the electrons free from atoms within the photovoltaic or solar cells in order to produce a flow of electricity. There are several solar cells that are connected together ( usually 60 or 72 ) in each panel. Individual cells comprises both a negative layer and a positive one which combines perfectly to create an electrical field in which the energy is generated.

The boron that’s within the bottom layer generates the positive charge, while the phosphorous found in the silicon layer produces the negative charge. In order to convert the sun’s rays into the energy that’s going to be transported from the panels to the inverter, the two field will interact with one another.

In other words, solar panels work by turning photons from the sunlight into direct current which is transmitted to the inverter. Once it gets to the inverter, it’s then translated to alternating current and send this current to to your electric box which powers the entire home. If you do not wish to reduce the high bills that’s associated with renting power from the grid, the solar energy system is an efficient and affordable way to achieve this aim.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

If you’re thinking of adding a solar battery to your home, you might be wondering whether or not it’s going to work in a power cut. If yes, then you’re not alone as this is one of the most common questions asked when it comes to solar batteries. In this post, we aim to provide you with a detailed answer to solve this concern once and for all.

The answer to this question is, it depends. The main reason why your solar batteries will usually not work or provide your home with the much-needed back up power is as a result of the several threats it poses. You should be aware that both your solar panels and battery are connected to the main grid. When a power cut occurs, your engineers will have to operate on the grid. If the solar panels or batteries are in operation at the period there’s a high chance the engineers would be electrocuted by the electricity that’s being produced. As a result of this, solar inverters are usually designed to automatically switch off once a power cut occurs. However, it should also be noted that if your solar battery possesses backup functionality, you’ll be able to make use of your solar energy in the event of a power cut. In other words, what determines if your home battery would work in a power cut is the availability or otherwise of a backup functionality.

Furthermore, you might also wish to know if your solar panels will continue to charge the battery in a power cut. Well, this depends on the type of backup system you possess. There are some more affordable batteries that are designed to automatically release their stored energy upon the detection of a power cut. And this is mostly because the battery inverter is usually smaller than the solar inverter which allows the energy from the solar inverter to the transmitted to the battery - risking an overload. However, if otherwise, then energy can continue to be transmitted to the battery until its fully charged.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

Whether installing an air source heat pump will help you save money depends on your property, how long you expect to live there, and the type of heat pump you get.

Air source heat pumps are initially quite expensive to install. However, if you get an air-to-water air source heat pump, you’re eligible for money from the Renewable Heat Incentive [https://www.energysavingtrust.org.uk/scotland/grants-loans/renewables/renewable-heat-incentive] (RHI). This is a UK government scheme that gives you quarterly cash payments over seven years if you install an eligible renewable heating technology (air-to-air air source heat pumps aren’t included).

All this means that if you have long-term plans to stay in your property, then an air-to-water air source heat pump can be a great way to save money on your heating bills. However, if you’re planning on moving out of your property relatively soon, or are a considering an air-to-air air source heat pump, it may not be the best financial option for you.

It’s important to remember that air source heat pumps are at their most efficient when installed in very well insulated properties. If your property’s not very energy efficient, you may find that a heat pump won’t help you save money.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Solar cells , also referred to as photovoltaic cells (PV), absorbs energy from the sun and converts it to generate electricity. This, however, should not be confused with photovoltaic thermal cells or PVT which operates to generate heat for water in homes. Solar cells are linked electrically and also carefully organized into a large frame which is popularly called solar panels. Generally, solar cells are produced or made of silicon semi conductors which works to absorb sunlight and then turn it into electricity for use at a home. A solar panel comprises of either 60 or 72 solar cells which are electrically interconnected in series and parallel and also positioned in between glass and plastic which is then framed.

At present, solar panels incorporated for residential or domestic purposes only possesses the capacity to make use of only about 20 percent of the sunlight they’re able to absorb and convert it to electricity - also called solar efficiency. Available in the market are also a wide range of solar cell available for both industrial and commercial purposes. This type of solar panels have an efficiency rating of about 40 percent which will also automatically make them more costly than the domestic types.

One great thing about the solar industry is the fact that it keeps improving in such a way that raises both its efficiency as well as overall quality. And with further research and development, this is expected to even increase as the years go by. What’s more? As these aspects keep rising, it’s also expected that the solar panels price should be on a decrease. That way, they’ll become available to a wider range of individuals who’ll also like to save money on electricity bills and go greener.