Find a Roofer you can trust in Badminton.

How you install commercial rubber roofing is similar to fitting it on a residential property, except that the area that’s covered is likely to be bigger. With commercial properties, you should always leave any maintenance and repair works to the professionals – whether you own or lease the property, you could invalidate any insurance if you try to install rubber roofing yourself. We’ll outline the steps roofers will take when installing rubber roofing on a commercial property.

Firstly, the installers will remove any existing coverings and clean and dry the surface thoroughly. This is vital in ensuring that the rubber will stick. They will then unwrap the EDPM rubber membrane and leave it to rest until it’s fully expanded. On a warm day this may take around half an hour.

Next, the roofers will work with half a sheet of rubber at a time and adhere it to the roof surface. They may use a water-based adhesive which they will spread onto the roof in sections, then roll the membrane onto the surface before moving onto the next section. If they’re using a bonded adhesive, they will apply it to both the roof and the rubber and leave it to dry until it’s tacky before extending the membrane.

Once the EDPM rubber is rolled out, the installers will brush the surface with a large broom to get rid of bubbles and provide a stronger bond. Then they will work of the edges, applying adhesive to roof and walls edges, sealing corners and creating watertight seals. They’ll also tidy up any excess membrane and seal all the trims.

As long as it’s installed correctly, your commercial rubber roofing should last you decades without any repairs needed. It’s always best to inspect your roof regularly to spot any damage before it becomes a bigger problem.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.

Most material warranties come from the waterproofing layer manufacturers, and can last between 5 and 20 years. If your roofing contractor is on the manufacturer’s installer list, it might cover their work. It’s important that you always read through all the information given to you about your warranty so you know exactly what is included.

Velux windows are a great way to add lots of light to your loft space. Velux is actually the name of a brand of roof window – not to be confused with roof lights, which are usually installed on flat roofs, or skylights, which are normally used to add natural light into a room without being able to open it. Roof windows open like regular windows and are fitted within your roof. But how much are Velux windows? Whether you choose a Velux window or another brand of roof window, they’re not cheap. Since they require special installation, including cutting roof timbers and replacing them to keep the structure strong enough, they take longer to install than a normal double glazed window. It can take up to a day to install a large Velux window, and it could set you back anywhere between £1,600 and £2,000. If you only need a small roof window in an area like a bathroom, you can expect to pay up to £1,300 for it to be fitted. Usually, there won’t be any need for scaffolding or towers because Velux windows are designed to be installed from the inside of your home. However, it’s worth setting aside an additional £500 in your budget in case unexpected problems occur and an installer needs to get on your roof to finish fitting the window. All of these prices are based on a standard roof window without any additional features. If you want to be able to control your windows with an electric switch or remote, this could set you back as much as an additional £400. For extra-low energy glass, you can expect to pay up to £200 more.

Chimneys are certainly on top of the commonly overlooked features when it comes to cleaning a house. This is quite understandable given the fact that they’re not readily accessible and not in plain sight, hence, home and property owners tend to overlook the relevance of any chimney cleaning effort. But this can be a grave mistake! The importance of having your chimney swept on a regular basis cannot be over emphasized and even more so if it happens to be on a wood burner. Not only can a dirty chimney constitute fire hazard, but when left uncleaned it can also give rise to blockages which can lead to carbon monoxide poisoning. In fact, from 2014 to 2018, one of the top factors contributing to about 25% of home heating fires is due to lack of cleaning, mainly from solid-fueled heating equipment, mostly chimneys. Therefore, sweeping your chimney regularly is a safety precaution and when they happen to be on a wood burner, this exercise becomes a lot more important. With that in mind, the question that arises is just how often is sweeping of a chimney on a would burner needed?

Well, it’s strongly advisable to sweep chimney on a wood burner at least twice a year by a qualified professional depending on the usage. If you happen to own an oil burning fireplace, the same also applies. In other words, this means that regardless of the type of chimney you possess, the cleaning must be done regularly. However, most chimney would only need to be swept once in a year by a qualified professional.

Whether you’re liable for a leaking roof in a commercial property will depend on your ownership status and any contracts. Of course, if you own a standalone commercial property, it would make it your responsibility to repair to leaking roof. But if you own an office within a building, you should check your paperwork to see whether you are responsible for some or all of a leaking roof.

If you’re a tenant in a commercial property, things get a bit more complicated. Lots of commercial leases are FRI, or Full Repairing and Insuring leases, which means that the tenant is responsible for all external and internal maintenance and insuring the building. It means that it’s vital that you read through your tenancy agreement in full before signing it and seek legal advice if you think you need it. If your lease is an FRI lease, you are liable for a leaking roof in your commercial property.

It’s important to ensure that you have a schedule of condition for the property, which will mean that you only have to restore the commercial property back to the condition that it was in when you took over. It’s also worth getting the roof inspected before you sign the lease, as if there is any damage before you sign the landlord may be responsible.

The best way to avoid having to pay for a leaking roof in a commercial property is prevention. If you are liable for repairs and maintenance, make sure you have the roof inspected regularly by a reputable company to avoid having to pay for costly repairs when disaster strikes.

How Much To Replace A Flat Roof

There’s no straight answer to this question. However, the average cost lies within the range of £1000 to £5000. This range may look too wide but the price is greatly influenced by a number of factors which is capable of making the price increase or decrease. Some of the factors affecting the cost of flat roof coverings and replacement include: the type of flat roofing system and materials you want, the area size of the flat roof in M2, the project’s location, the roofing company to be used, the ease at which to reach the roof, cost of removing the old flat roof as well as cost of removing the other waste.

Although there are many factors to be put into consideration but the most crucial factor is the size of the house or the area size of the flat roof in M2. for instance, a one bedroom apartment’s flat roof will have a price between £1500 to £3000. This is, however, with the assumption that the flat roof is going to be used as the main roof of the house. But if you’re only using it for a section of the house like your garage, the price could range between £700 to £1000

There four commonly used types of flat roof materials which includes fibreglass, felt, rubber and lead. If you need a felt roof, for example, the price is between £40 to £70 per m2. And in the same tone, a metal roof will generally cost more than a a flat roof made from rubber.

Another important factor we’ll discuss is the labour or the roofing company to be used. Different roofing companies will charge different prices. As a result, you should carefully compare the prices of the companies in order to get a great deal.