Find a Roofer you can trust in Aberlour.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

You should inspect your roof at least once a year, to check there are no leaks or infestations. It’s best to do this just after it has rained, so leaks are as obvious as possible. You may find over a period of time there is a build up of moss on the roof, this should be cleaned so rain water has a clear path to the guttering.

Most Sun Tunnel Kits are available in sizes from 250mm Diameter to 550mm Diameter. This gives you a good range to choose from depending on the size of the room you are trying to brighten.

• 250mm Sun Tube – Perfect for room sizes up to 10m2. (Hallways, Small Bathrooms)
• 350 – 450mm Sun Tubes – Perfect for rooms 10 to 15m2. Larger Hallways, Stairwells and Bathrooms.
• 550mm Sun Tube – Ideal for rooms 15 – 22m2. Kitchens, Bedrooms, Living Rooms.

If you’ve never had Velux windows before, you might be wondering how to open them. If you’ve got very high ceilings and your roof windows are set high up in the pitch of the roof, you might not even be able to reach them. So how do you open them in this case?

When Velux windows are installed so high that they’re out of reach, the installers will often recommend that they install an electric switch for you to open and close your windows. They often come with a rain sensor, so you don’t need to rush up to the top of the house if there’s a sudden downpour – they will close automatically. You can also choose to have a remote so you can open and close your roof windows wherever you are in the room.

If you don’t have an electric switch, but you still can’t reach to open and close your Velux windows, you should be supplied with a telescopic pole when they’re installed. If you weren’t or you’ve moved into a home with roof windows and there isn’t one, you can buy them online. They have a hook on the end and can be extended to the correct length so you can hook it over the handle of the window and pull or push to open it.

If you’ve got a top-hung Velux window that can also be opened in a centre-pivot position, it’s easy to switch between the two. Simply ensure the window is completely closed before you start, then open the handle up – but don’t push it out. Then pull the vent bar down until the sash is rotated 180 degrees. Then secure the position by sliding the barrel bolts into the holes at either side of the bottom of the frame. Easy!

It depends on the material you use, but if your flat roof is installed correctly it should last for at least 10 years, and at least 20 if a material other than felt is used. Always question a roofing company when they quote to find out what materials they use and what guarantee's they offer.

Fibreglass, or GRP, flat roofs are very durable and should last you years, but over time they can become brittle and you might see some cracks or holes forming. Luckily, you can repair a fibreglass flat roof and it doesn’t have to be too difficult. Cracks in a fibreglass flat roof If you notice long cracks in your fibreglass roof, you can often use a fibreglass crack sealant. Simply clean the area, squeeze the sealant into the crack, then smooth it off. If you want it to look neater, you could coat the entire roof with a restorative coating which will make it look new again. Hole in a fibreglass roof If you notice a hole in your fibreglass flat roof, you’ll want to get this repaired as soon as possible to avoid any rainwater getting into your home. There are lots of fibreglass roof hole repair kits on the market, both online and in DIY stores, so you shouldn’t have trouble picking one up. They usually contain a mouldable UV cured patch that you can stick onto the hole. It will harden and become instantly weatherproof, so is the perfect emergency repair solution. Fixing pin holes in a fibreglass flat roof Unfortunately, if you find pin holes in a fibreglass flat roof it’s often because the installer didn’t use enough resin during the fibreglassing process. Luckily, if you can’t get back in touch with the installer or you only notice after a few years, you can fix this yourself. Sand down the roof back to the clear resin layer. Clean the entire roof with acetone and reapply some GRP roofing resin. Ensure that all the pinholes are filled – you might need two coats.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.