Find a Roofer you can trust in Prestonpans.

While it sounds like it could be difficult to plasterboard around a Velux window, it needn’t be. As long as you have the right tools and materials, you should be able to plasterboard around your roof window easily and make good ready to be skimmed. When you or a tradesperson has fitted your Velux window into your roof, you’ll probably need to plasterboard over it to create a good ceiling. To do this, you’ll need:

• Plasterboard sheets – make sure you measure your room so you know how much you’ll need
• Screws to secure the board in place
• Drill
• Hammer
• Straight edge and pen knife to score the board before trimming
• Fine toothed saw the cut the plasterboard

When you’re ready to plasterboard around your roof window, make sure you’ve cleared enough space to work in. Then you can begin by cutting your plasterboard to size using your straight edge and pen knife to score, then your saw to get a clean cut. A common way of plasterboarding around your Velux window is to use the groove on the window frame to hold one edge of the board, then screw the other edge to the battens on the ceiling. People often use drywall screws these days as they have a better grip of the plasterboard as they drive through. You’ll need to use a drill to screw these in. However, you could use plasterboard nails, which are galvanised to stop rusting. When you’ve done this, you can then skim the walls or ask a plasterer to do it for you. Plastering, while it looks easy, is a tricky skill so it’s always best to ask a professional to do it.

One of the most popular choices for roofing materials are roof slates. There is a number of advantages that a roof slate has, hey can be aesthetically pleasing, they can also increase the potential selling value of the house and many more. Slate is a sturdy and resilient material that delivers waterproofing physical characteristics to a pitched roof. Unlike other roof materials which absorb water slates do not. Therefore, slate is the most resistant towards freezing and water damage.

Find out the pitch of your roof

Before beginning with the fitting procedure, you need to figure out the pitch of your roof. The roof pitch commands how much overlap is essential with each slate. This has been made a lot easier than the early days with the advancement of technology.

Find out the required overlap

Once you’ve found out the exact pitch of your roof accurately, take a look at the slate producer’s description. Each manufacturer will propose the obligatory overlap in order to form a firm and safe slate roof.

Roll out the roof membrane

Firstly, guarantee your joists or trusses are clean of any sheards or old nails that could harm the membrane. You will now have to roll the chosen roofing membrane along the roof trusses. It is always wise to start from one of the bottom corners and keep rolling it along to the other corner.

Secure the roof membrane

Once the membrane has been moved out, use thump nails to protect one edge. You will now have to pull the membrane taut and carefully fix it into position. Do this before adding any nails across the membrane at points of intersection with the trusses for extra stability.

Batten placement

This is done to find the proper assignment of the battens. For this, you will need two full-sized slates along with an under eaves slate. Carefully position the battens on the top of the roof on the top of the overlay. Make sure not to fix them down since it will be easier to move them around and make any adjustments.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

Knowing when best to clean your gutters can do a lot of good. Wile some people assume that fall is the best time for gutter cleaning after the leaves fall, others believe spring is the most appropriate time to clean the gutters before things start to grow there. The truth is, both camps are right. However, the best time to clean your gutters depend on a wide range of factors which are all unique to you. In order to help you make the most informed decision possible, we have created this post to help you figure out the right time to clean your gutters. Let’s take a look!

Where you’re located. What we get is four season in a year as well as as a good amount of rain. As a result, you may want to put into consideration cleaning your gutter at least twice a year - clean the gutters once in the spring and once in the fall. It’s important to make gutter cleaning a part of your normal spring schedule as well as part of your fall maintenance routines.

What surrounds your home. If you happen to have tree surrounding your home, then it’s more likely that dead leaves clog up your gutter pretty quickly. A single tree is enough as it’s going to shed leaves that will find their way into your gutter, accumulate and affect its performance and integrity.

What your gutter currently looks like. If you gutters already have an entire ecosystem of animal life and plants hamging over the edges, then the best time to clean the gutters is now rather than having to wait a particular season to act. A dirty gutter should be attended to immediately in order to prevent some unnecessary damages as well as expensive repairs.

The cost for a sun tunnel is affected by 5 key factors:

1. Tube size: Small areas or stairways can gain from a 10-inch size tube, whilst bigger rooms will require a bigger tube. The higher television size, the greater the price.
2. Kind of tunnel and also roof type: You can pick from stiff or flexible tunnels and also domed or flat roofing system panels. Each choice will have a different price.
3. Place: Where you stay in the country will certainly impact the price of your sun tunnel installation. Generally, the higher the living prices in your location, the greater the price of employing an expert will certainly be.
4. Length of the tunnel: Longer tunnels will be charged at a greater price than their shorter equivalents so whether the tunnel runs from the roof to the 2nd or very first flooring will certainly impact the sun tunnel price.
5. Ease of gain access to: Flexible tubes are fantastic for homes where sun tunnels do not run in a straight line from roofing to ceiling. The tubes can then be fitted around challenges in your loft space. Frustratingly, these alternatives do not allow as much light as stiff tubes and also due to their hard setup can be much more expensive.

There are a few reasons why commercial buildings often have flat roofs. Lots of people argue that flat roofs aren’t as attractive as pitched roofs, which is why it’s uncommon to see a residential property with an entirely flat roof. Lots of commercial buildings don’t need to look attractive, so go for flat roofs because they’re cheaper.

Flat roofs tend to be less expensive than pitched roofs, especially for large, broad commercial buildings. Some commercial buildings simply couldn’t have a pitched roof because their width would mean that the roof would have to be extremely high. Flat roofs are also cost-effective for commercial buildings because it means that air conditioning and ventilation units can go on the roof, saving space in and around the building.

Commercial buildings also often have flat roofs because they don’t need the loft space that residential properties need. If there’s no need for the space, it doesn’t make sense to spend more money on a pitched roof just to keep the attic space empty. Flat roofs also give the commercial building owner the opportunity to use the space as a smoking area for employees or give access to fire escapes to upper floors.

If you’re having a commercial property build, make sure you speak to the experts about the type of roof that is suitable for you. If you’re planning on having air conditioning or ventilation systems installed within the property, you might be best off with a flat roof – but if you need some extra storage space, a pitched roof might work best for you.

How to repair a hole in a flat roof depends on what material your flat roof is made from. If you have an asphalt, felt or EDPM rubber roof, the repairs are quite simple, whereas it’s a bit more tricky if you have a fibreglass flat roof. How to repair a hole in an asphalt flat roof If you’ve got a small hole in your asphalt flat roof, you might get away with using a paint-on fix from a tin. It’s best to use this as a temporary measure to tide you over until you can get in touch with a professional. If the hole is on the flashing, you can add heat-applied flashing tape to it, or use a patch of torched-on roofing felt. There are liquid systems you can use, but usually they’re only available to the trade. Repairing a hole in a felt flat roof It's a similar process to asphalt roofing if you want to repair a hole in a felt flat roof. Use a paint-on fix for a temporary solution, but the best way to repair a hole is to use a torched-on piece of roofing felt to cover the hole and make it watertight again. How to fix a hole in an EDPM rubber flat roof If the hole in a rubber flat roof is small, you may be able to get away with applying some lap sealant to the hole. Only use a small amount, as if you go for a more permanent repair later down the line all of this will need to be scraped off. You can also use a malleable piece of self-adhesive flashing – clean the area, add EDPM primer and stick the patch on from the centre outwards. Add sealant to the edges if you want to give it more water protection. How to fix pin holes in a fibreglass flat roof If you find pin holes in your fibreglass roof, it usually means there wasn’t enough resin used at installation. To repair the holes, you’ll need to sand down the entire roof back to the clear resin. Then clean the area with acetone and apply GRP roofing resin – the acetone ensures that the resin sticks. You might need two coats of resin to get rid of all the holes.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.