Find a Roofer you can trust in Mayfield.

Commercial roofing simply refers to any roofing work, including installation and repair, that is done to commercial buildings. This might include office roofs, shop roofs or commercial unit roofs. Every building needs a roof to keep out the rain!

Since looks aren’t usually the first priority with commercial buildings, lots of commercial properties have flat roofs. These are often made from felt, EDPM rubber or fibreglass. Felt is the cheapest commercial roofing material, while fibreglass tends to be the most expensive. In felt roofs, roofers use an adhesive to stick roofing felt onto a frame. EDPM rubber roofs have a rubber membrane that is laid down and glued onto the roof and coated with a contact adhesive, while fibreglass uses a cut glass fibre mat that is pressed on before a resin and topcoat are applied.

Not all roofing companies will offer commercial roofing services, because generally the buildings tend to be bigger. Small companies won’t have enough tradespeople to work on a roof without making it very expensive for you. Commercial buildings also tend to need more scaffolding to make it safe for the professionals to work, so some smaller roofing companies won’t offer commercial services. Make sure you check a company’s website or social media if you’re looking for commercial roofing – on the Quotatis Directory, our roofers will show whether they do commercial roofing to make your search easier.

How To Clean Roof Tiles?

If you’re a DIY person with a dirty roof tiles or just a homeowner who’s also a lover of knowledge, you may probably like to know how you can have your roof tiles cleaned. This is a very common question which often depends on the dirt or debris you’re dealing with as well as the type of roof you possess. Most often than not, if you own a traditional concrete or slate roof tiles, then you’re more likely to battle moss and or algae growth.

If you’re not a competent DIY person or do not have enough confidence to pull this off, then it’s advisable to hire the services of a professional who can guarantee the best results for help. In this article, you’ll learn how to go about cleaning your roof tiles. Let’s have a look!

✓ Consider Safety. When it comes to roof cleaning, you have to be very careful. They’re normally high up and any task that deals with height will usually require putting safety measures in place. Firstly, it’s important to be confident with heights and ladders, if not you’d have to find someone who is. And if you’re confident, there’s also the need to find someone who can help you hold the base of the ladder.

✓ Trim the trees. Nearby trees are usually a threat to any roof and also makes cleaning much harder. So it’s always wise to cut any overhanging branches before you proceed.

✓ Bleach or not to bleach. Although you have to be very careful using beach and water but it also happens to be one of the easiest DIY ways to clean your roof. You either stand about 4 feet away and rely on water pressure or clean down the tiles by hand.

✓ Try not to make use of a blaster.

Ponding is where you see pools of water appearing on your flat roof. Unless your roof is leaking or showing other signs of damage, you don’t need to replace it. When you do have your flat roof replaced, tell the contractor so they can find out the cause of the ponding.

How Much To Replace A Flat Roof

There’s no straight answer to this question. However, the average cost lies within the range of £1000 to £5000. This range may look too wide but the price is greatly influenced by a number of factors which is capable of making the price increase or decrease. Some of the factors affecting the cost of flat roof coverings and replacement include: the type of flat roofing system and materials you want, the area size of the flat roof in M2, the project’s location, the roofing company to be used, the ease at which to reach the roof, cost of removing the old flat roof as well as cost of removing the other waste.

Although there are many factors to be put into consideration but the most crucial factor is the size of the house or the area size of the flat roof in M2. for instance, a one bedroom apartment’s flat roof will have a price between £1500 to £3000. This is, however, with the assumption that the flat roof is going to be used as the main roof of the house. But if you’re only using it for a section of the house like your garage, the price could range between £700 to £1000

There four commonly used types of flat roof materials which includes fibreglass, felt, rubber and lead. If you need a felt roof, for example, the price is between £40 to £70 per m2. And in the same tone, a metal roof will generally cost more than a a flat roof made from rubber.

Another important factor we’ll discuss is the labour or the roofing company to be used. Different roofing companies will charge different prices. As a result, you should carefully compare the prices of the companies in order to get a great deal.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

As long as you can access them safely, it’s fairly easy to clean soffits and fascias. Using a sponge and warm water to scrub them is a good way to get off most types of dirt. You might want to add detergent or bleach to the water to make it more effective.

Once you’ve scrubbed your soffits and fascias, rinse them with clean water to make sure you’ve got all of the dirt and detergent off.

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.

A Velux window is a brand of roof window, but the brand is so popular that people often use the name to describe the entire type of window. They are windows that are installed at the same orientation and ‘in plane’ with the surrounding roof, and they’re usually installed at a minimum of a 15-degree pitch. You can buy roof windows that offer completely frameless internal views for a really clean look in your loft conversion, while some come with built-in shutters.

Velux windows aren’t to be confused with rooflights which usually refers to a glazed unit that’s installed on a flat roof. It might also mean a window that’s been installed on a pitched roof out of plane with the level of the tiling.

People also confuse roof windows with skylights, which normally can’t be opened or closed and are usually smaller than Velux windows. Skylights, therefore, only let daylight into the room whereas roof windows also help with ventilation.

If you’re using your loft as a room in your home rather than simply for storage, you must have a roof window installed. Skylights won’t be enough as they don’t allow for ventilation. It doesn’t have to be a Velux window – it can be any type of roof window. Luckily, they tend to come in standard sizes and they must be CE marked if they’re sold as a roof window, so they should be easy to find.