Find a Roofer you can trust in Peacehaven.

How To Clean And Maintain Metal Roofs

If you already have a metal roof or just planning to get one, you’d probably be interested in knowing the cleaning and maintenance procedures. Although, metal roof are widely known to be very easy to clean and maintain and also very durable and long lasting, it’s still strongly recommended that homeowners should do all in their power clean and to take care of their metal roof in order to ensure it they live up to their potentials. Cleaning your metal roofs regularly helps to minimize damaging element such as airborne dirt, pollen, organic material debris, pollution, mildew and lots more. If left unattended to, these unwanted elements can result in several negative issues over time as such as chalking. Due to fact that metal roofs normally features special coatings as well as paint, cleaning the roof is both easy and environmentally friendly, which removes the need to use toxic chemicals. With just plain water, you can effectively wash down dirt, dust and other debris from your metal roof.

While the cleaning process is quite simple, working at height can be incredibly dangerous. It requires skills and confidence, so if you lack either of these qualities, it’s advisable to call in a professional roof cleaning contractor for help. Below is a simple cleaning solution usful for most metal roofs.

✓ In the event whereby water alone isn’t enough, make a cleaning solution using a quarter cup detergent ( which should include car washing soap, mild laundry detergent, mild dish soap) for each gallon of water.

✓ Apply the mixture to the surface of the roof with a wash cloth and ensure to the application gently.

✓ After application, allow it sit for up to 15mins.

✓ Rinse the roof surface with plain water.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Tar and gravel flat roofs are popular because the gravel weighs down the surface of the roof so it doesn’t blow away and it also protects it from sun damage. The tar makes the roof watertight, so you won’t get any leaks. However, sometimes problems occur and you’ll get cracks and leaks. So how do you repair a tar and gravel flat roof?

If you notice leaking coming through your flat roof, try to find the source of the leak. Since water can travel easily, it might not be where you think it is. The first place to check is the flashing, then any parts of the roof with gravel missing. Once you’ve found the crack, sweep away any remaining gravel and clean the area.

Apply a primer to the area and allow it to dry. Then, apply a tar and gravel roof patch that you can get from most DIY shops. Patch 2-3 inches around the damaged area, creating layers, and ensuring that there aren’t any air bubbles or gaps. Then you should cover the entire patch with gravel.

Before you try to repair a tar and gravel flat roof yourself, consider how much of the roof needs repairing. Professionals often say that if cracks and faults make up 25% or more of the roof, then you should look to replace it. It might be tempting to try and replace your tar and gravel roof yourself, but it’s best left to the specialists. They will ensure that your new roof is watertight and strong enough to withstand sun damage and storms.

How to repair a hole in a flat roof depends on what material your flat roof is made from. If you have an asphalt, felt or EDPM rubber roof, the repairs are quite simple, whereas it’s a bit more tricky if you have a fibreglass flat roof. How to repair a hole in an asphalt flat roof If you’ve got a small hole in your asphalt flat roof, you might get away with using a paint-on fix from a tin. It’s best to use this as a temporary measure to tide you over until you can get in touch with a professional. If the hole is on the flashing, you can add heat-applied flashing tape to it, or use a patch of torched-on roofing felt. There are liquid systems you can use, but usually they’re only available to the trade. Repairing a hole in a felt flat roof It's a similar process to asphalt roofing if you want to repair a hole in a felt flat roof. Use a paint-on fix for a temporary solution, but the best way to repair a hole is to use a torched-on piece of roofing felt to cover the hole and make it watertight again. How to fix a hole in an EDPM rubber flat roof If the hole in a rubber flat roof is small, you may be able to get away with applying some lap sealant to the hole. Only use a small amount, as if you go for a more permanent repair later down the line all of this will need to be scraped off. You can also use a malleable piece of self-adhesive flashing – clean the area, add EDPM primer and stick the patch on from the centre outwards. Add sealant to the edges if you want to give it more water protection. How to fix pin holes in a fibreglass flat roof If you find pin holes in your fibreglass roof, it usually means there wasn’t enough resin used at installation. To repair the holes, you’ll need to sand down the entire roof back to the clear resin. Then clean the area with acetone and apply GRP roofing resin – the acetone ensures that the resin sticks. You might need two coats of resin to get rid of all the holes.

Chimney liners are a very important component of the chimney, but the fact is most home and property owners either continue to overlook them or aren’t even aware of their existence. This is, however, quite understandable given the fact that they usually last a long period of time – more than 50 years. To ensure that they last that long, the question that arises is, do chimney liners need to be swept and cleaned? The short and simple answer to this question is yes, chimney liners definitely needs to be cleaned on a frequent basis. A chimney liner happens to be an essential part of your chimney. When it’s not cleaned, it tends to accumulate dust, soot and dirt which can give rise to a number of problems you’d rather want to avoid. Chimney liner are able to provide adequate protection to your flue but even at that the water, creosote and other contaminant build up can make the liner to deteriorate, and making it unsafe for usage. In other words, contrary to several belief, chimney liners do need the same amount of cleaning as chimneys without liners. Failure to sweep your chimney liners can give rise to the following problems:

• Creosote buildup. If your main source of fire is wood, then you’ll definitely have creosote present in your chimney. This is highly combustible and its buildup may lead to fire outbreak.
• Carbon monoxide poisoning. Carbon monoxide is said to be on the rise by NCBI and its primarily generated from heating systems which are terribly ventilated as a result of uncleaned or dirty chimneys.

A Velux window is a brand of roof window, but the brand is so popular that people often use the name to describe the entire type of window. They are windows that are installed at the same orientation and ‘in plane’ with the surrounding roof, and they’re usually installed at a minimum of a 15-degree pitch. You can buy roof windows that offer completely frameless internal views for a really clean look in your loft conversion, while some come with built-in shutters.

Velux windows aren’t to be confused with rooflights which usually refers to a glazed unit that’s installed on a flat roof. It might also mean a window that’s been installed on a pitched roof out of plane with the level of the tiling.

People also confuse roof windows with skylights, which normally can’t be opened or closed and are usually smaller than Velux windows. Skylights, therefore, only let daylight into the room whereas roof windows also help with ventilation.

If you’re using your loft as a room in your home rather than simply for storage, you must have a roof window installed. Skylights won’t be enough as they don’t allow for ventilation. It doesn’t have to be a Velux window – it can be any type of roof window. Luckily, they tend to come in standard sizes and they must be CE marked if they’re sold as a roof window, so they should be easy to find.

In the UK, fireplaces are a very common addition to homes and property and reasonably so. Not only do they represent a great source of heat, but they’re also quite timeless in their beauty, thereby adding more value to your property. Now every fireplace possesses some sort of chimney, asides from the ones that are ventless. And while you might not be aware, every chimney poses a number of dangers which includes being a fire hazard and can also lead to carbon monoxide poisoning as a result of improper or lack maintenance.

Since your chimney will be clogged up over time with all sorts of soot and often cleaned from the top of the roof, cleaning of a chimney comes with a huge amount of risk. As a result, you run the risk of falling off if you decide to clean one by yourself. And even if you’re the type that’s comfortable being on high level places, you should know cleaning a chimney is not the most pleasant of jobs. It can be quite messy as accumulated creosote and soot can drop into your home causing a cloud which covers both the floor, furniture and any other thing you have in the room. Furthermore, chimney cleaning requires specialized skills and knowledge which professionals have acquired after several practices. For instance, missing out on a spot can result in an unchecked chimney fire or a masonry crack.

The simple answer to this question is, therefore, a big NO - you should leave the cleaning to the professionals.  Professionals are not just limited to chimney cleaning; they’re trained to identify any structural issues while also being able to carry out a close analysis of the chimney. They’ll fix minor issues on site and give you a peace mind for any future wood burning activities.