Find a Roofer you can trust in Uckfield.

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.

It can be easy to repair a felt flat roof depending on the problem. If you’ve got an old-style pour-and-roll felt flat roof, you might be starting to run into problems, but even if you have a newer torch-on felt roof, issues can occur. You might find cracks, lifting, leaking flashings or dips and hollows in the felt. Luckily, there are some easy fixes – but the best thing to do to prolong the life of your felt flat roof is to get a professional to look at it.

If your felt flat roof only needs a small repair, you might be able to get away with using a paint-on fix from a tin that you just brush on. However, if you want a more permanent fix, you’ll need a few more tools and supplies.

You can use a patch of torched-on roofing felt over the crack or leak, but if your flat roof is very damaged or wet it might not take it. You can also buy liquid systems for felt roofs, but again, there is a possibility that your roof might not take it. Also most of the high-quality liquid systems are only available for trade customers, so you might be better off asking a roofing pro to do it for you.

How To Clean Concrete Roof Tiles

Dirt, moss and algae usually sees concrete roof tiles as the perfect place to reside. They can damage the structural bonds of your roof, they can lead to overheating of the attic and roof space as well as blocked gutters. In order to protect the structural integrity of your roof and ensure your home and properties are well protected against the elements, it’s therefore crucial to clean your roof regularly. There are plethora of ways to go about this but which method will best suit your concrete roof tile?

When it comes to working at heights, skill and confidence is paramount even if the actually cleaning and maintenance happens to be an easy task. As a result, if you lack the two attributes mentioned, we’d strongly recommend that you call in a professional roof cleaning contractor who can guarantee the best results for help. In this article, we aim to give you a good insight into the concrete roof tiles cleaning process. Let’s have a look!

✓ Use a trowel or stiff brush

This is a manual method which involves scraping off the algae, moss and dirt by hand using an effective tool like a trowel. However, before you do this make sure its a very dry day. Also, you can make use of a stiff brush to scrape off the dirt. Both cleaning tools are very easy and effective means to clean concrete roof tiles.

✓ Use chemicals

You can apply fungicide, moss killers and anti moss treatments with the help of a spray to kill any plant life on your concrete roof tiles. However, you should only do this after you’ve successfully scraped the surface with a trowel or a stiff brush.

How To Repair Roof Leak

Asphalt shingles are the most popular roofing material options for most UK homes in recent times. Thanks to them, roof repair is now all about identifying the leak and sealing it the right way. If you’re a competent DIYer and confident enough to pull this off, then this should be done within a short period of time and saving you money as well. However, if you don’t have the confidence to pull this off, then calling on a professional roofer who can guarantee the best results will be your best bet. In this article, we’ll consider four simple steps you can take to repair an asphalt shingles roof.

✓ Locate the spot of the roof leak. Roof leaks are mostly made evident by water stains on the ceiling. Simply note the spot of this water stain, grab a good pair of binoculars, then go outside to identify the location of the roof leak. Search the area for any curls, cracks, missing shingles or anything that looks odd. Leaks can also occur at any spot where caulking and flashing have been affected or compromised.

✓ Secure curled shingles. To do this, simply brush on a generous amount of asphalt roofing cement to the underside of the shingle and press firmly to set.

✓ Replace damaged or missing shingles. In the event whereby the shingles are cracked, rotten or missing, your best bet would be to have them replaced. Simply remove the damaged shingle then slide in the new one under the one above and align it with those on either side. Once done, you can then secure it with 6d galvanized roofing nails at each corner. After completion, make sure you cover the nail heads with roof cements.

✓ Fix flashing. To do this, simply reseal joints with the help of a caulk gun loaded with roofing cement.

How To Clean A Roof?

If you’re planning to clean your roof, but don’t know where to start, you’ve come to the right place! There are different types of roofs available in the market today and the method used in cleaning one can be largely different from the other. As a result, we’re only going to look at one of the common types of roofs you’ll find in the UK - the Asphalt shingle roof tiles. This roof type is very common and for a good reason. Not only are they visually appealing but they’re also hugely versatile by design which enables them to be adaptable to varying shapes, angles as well as forms depending on your preference or needs. With all the benefits that can be derived from asphalt shingle, they however, need to be properly maintained to help retain their good looks.

To clean your asphalt shingles, you’ll most likely require some type of chemicals especially when dealing with algae stains and some other visual problems. Therefore, make sure you purchase a product marked safe to be used on this type of roof and not those only proven to remove moss and algae stains. Mix the chemical cleaner with a gallon of water and a quart of bleach or as instructed by the manufacturer. Pour the mixture inside a pump-style garden sprayer and mix thoroughly. When done, climb up on the roof and spray as good as you can. Upon completion of spraying the roof with the mixture, then allow to work its magic for some time - about 15 minutes or thereabout should be good.

After that, you can make use of a garden hose to spray down the roof and wash down the mixture entirely. If some stains remain, use a brush to gently wipe the tiles individually.

It depends on the material you use, but if your flat roof is installed correctly it should last for at least 10 years, and at least 20 if a material other than felt is used. Always question a roofing company when they quote to find out what materials they use and what guarantee's they offer.

How to repair your flat garage roof will depend on what it’s made from. Lots of flat garage roofs are made from EDPM rubber, asphalt or felt. We’ll explain how to carry out repairs on your garage roof here. EDPM rubber flat roof repair EDPM rubber is an excellent choice for a flat garage roof and should need little maintenance. But if you do need to repair it, there are a few easy fixes. If it’s a small crack or tear, apply some lap sealant to the area, but don’t use too much. If you go for a more professional repair later, the sealant will need to be scraped off, so if there’s too much it might cost you more in labour. If you need to repair the flashing, buy some malleable flashing tape so you can form it into the right shape. Clean and dry the area that needs repairing, then apply an EDPM primer. When that’s touch dry, stick the patch of flashing tape down from the centre outwards with a roller. Repairing an asphalt flat garage roof Asphalt is also very hard-wearing, and when it does need fixing, the fixes often last a long time. So if you do get cracks or blisters, you can use a paint-on fix from a tin as a temporary repair. When it’s time for a more permanent fix, you can add a small patch of torched-on roofing felt or use a liquid system, but the high-quality ones are often only available to trade customers. How to repair a felt flat garage roof Felt can be repaired in a similar way to asphalt flat garage roofs. For small cracks or a temporary fix, try a paint-on treatment from a tin. But for something more permanent, use a patch of torched-on roofing felt or a liquid system. If these don’t stick, unfortunately it means it’s time for a new felt garage roof. If you do need a new flat garage roof, leave it to the professionals who will ensure that your new roof will last for years.