Find a Roofer you can trust in Cwmbran.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

A roof is one of the most significant portions of any property and they’re also the single part of a structure most vulnerable to impairment from the elements. If your roof suffers substantial damage over time, maintenances and re-roofing charges can be expensive, time-consuming, and stressful which is why it is imperative to keep your roof in sound structural and aesthetic order.

If a tile has fallen off from the top of your roof – you can expect to pay around £70-£100 to replace it including a different tile fitted in its place. Replacing a hip roof will cost between £4,250 and £7,250, the cost varies if you have a single valley or a double valley on your roof. For a new gable roof, you should expect to pay around £3,250 to £5,250.

What does it cost to replace my roof?

The charge of substituting your roof for a new one will be subject to the age and condition that it’s in, but usually, the cost of a new roof on an average property is around £5,500.

Some of the key factors to keep in mind when calculating the cost of re-roofing your house include:

• size of your roof

• type and size of the materials used

• shape and style of the roof

• If structural changes are required or not

• the roofing company hired

Tiled roof repair costs

If you are trying to prevent water from leaking inside your house for one or two tiles, then you can expect to pay between £100 to £200 to fix them and seal the leaks.

Flat roof repair costs

Minor jobs such as repairing flat roofs as well as sheds and garages or mending blisters can usually cost around £300.

Roofing job Price range

Replacing six ridge tiles £135-£260

Replacing six broken or missing tiles £55-£105

Cleanout of your gutter £35-£80

Replacing one right tile on rooftop £70-£100

The cost of a full re-roofing job can amount to around £3,250 to £7,250 depending on the size of your property.

Hip roof Cost range Length of time

Semi-detached home £4,250-£4,750 3-4 days

Detached home £5,250-£5,750 4-5 days

2 valleys – semi-detached home £5,750-£6,250 5-6 days

2-valleys detached home £6,750-£7,250 6-7 days

Gable roof Cost range Length of time

Standard £3,250-£3,750 2-3 days

2-valley £4,750-£5,250 4-5 days

The feasibility of this will depend on the roof’s strength, in particular its load bearing capabilities. This is simply because tiles are heavier than the metal sheeting. Normally a tiled roof will need to take a load capacity of 60kg per square metre. You will need a trusted roofing company to advise on this.

Will My Roof Leak With Missing Ridge Tiles?

Your roof is the first line of defence against the elements. Therefore, if you want your home protected at all times, there’s a need to ensure a professional inspection of your home at least once a year. However, there are certain issues that you do not have to wait for a professional to be able to spot by yourself. And an example of this includes a missing ridge tile. This issue is noticeable from the ground level while some tiles may even fall off and notifying you in the process. If you’re currently facing this kind of challenge, you’d probably want to know if the missing ridge tiles can cause your roof to leak. In this article, we aim to answer this question and more. Let’s take a look!

Firstly, there are a number of causes of missing tiles or slates and the most obvious is the weather. When the wind or rain gets very high, it can pull your tiles out of place and even more more, if they weren’t properly installed in the first place. Secondly, there’s also a chance that the nails may wear away. These are the nails that holds your ridge tiles in place, they can rust and wear away, hence leading to missing ridge tiles.

Therefore, the short answer to the question is yes, missing ridge tiles can cause your roof to leak. Even if it doesn’t leave a visible gap in your roof’s covering, it’ll create a break in the roof which weather can easily penetrate. And allowing this to happen makes the other tiles more susceptible to damage which won’t be good for the entire house as well as your pocket. Hence, once you notice a missing ridge tile ensure to have it replaced as soon as possible.

How Much Is It To Replace A Garage Roof?

The size of your garage will be the main determinant of the cost of a new garage roof. However, the present condition of your roof structure as well as the type of roof covering preferred are also huge factors. In the UK, the cost of a garage roof replacement will be within the range of £700 to £3600.

The first step a pro will take is to remove the existing roofing while also making sure that the timber structure is in a good condition. In the event whereby the timber is rotten, it will need to be replaced before the installation of a new roof. If the garage roof sheets needs a replacement, you’ll have to spend about £30 to £50 per each garage roof sheets. Individual plywood sheet has around 2.4m x 1.2m in measurement and whose price should also be included in the final cost.

The above information applies only to standard roofing for garage roofs with flat roofs being made of bitumen felt and asphalt. In recent times, this is no longer the case with several more options available. Today, EPDM and GRP fibreglass have rapidly become very popular amongst several homeowners in the country. It’s also important to note that modern roofing has greatly advanced over the years even though both EPDM garage roofs and GRP fibreglass garage roofs are way better and of more quality when compared to felt and asphalt roofs. And thanks to modern technology, modern garage roofing possesses a longer life expectancy and as result, are a lot costlier than the conventional ones.

For a medium size single garage (2.7m x 5.5m), the cost for a felt roof per square metre is between £40 to £70, while that of a fiberglass roof and an EPDM rubber roof is between £90 to £110 and £70 to £100 respectively.

Chimneys are certainly on top of the commonly overlooked features when it comes to cleaning a house. This is quite understandable given the fact that they’re not readily accessible and not in plain sight, hence, home and property owners tend to overlook the relevance of any chimney cleaning effort. But this can be a grave mistake! The importance of having your chimney swept on a regular basis cannot be over emphasized and even more so if it happens to be on a wood burner. Not only can a dirty chimney constitute fire hazard, but when left uncleaned it can also give rise to blockages which can lead to carbon monoxide poisoning. In fact, from 2014 to 2018, one of the top factors contributing to about 25% of home heating fires is due to lack of cleaning, mainly from solid-fueled heating equipment, mostly chimneys. Therefore, sweeping your chimney regularly is a safety precaution and when they happen to be on a wood burner, this exercise becomes a lot more important. With that in mind, the question that arises is just how often is sweeping of a chimney on a would burner needed?

Well, it’s strongly advisable to sweep chimney on a wood burner at least twice a year by a qualified professional depending on the usage. If you happen to own an oil burning fireplace, the same also applies. In other words, this means that regardless of the type of chimney you possess, the cleaning must be done regularly. However, most chimney would only need to be swept once in a year by a qualified professional.

How long it takes to fix a roofing sheet on a commercial property will depend on the size of your roof and how difficult access is. Corrugated iron roofing sheets are much easier to fit than other roofing materials such as clay tiles or EDPM rubber, so that will work in your favour.

The size of the team of the roofing company you engage will also make a difference. If they have a lot of tradespeople working on your roof with lots of experience, it will take less time, while if there are only a couple of people it will take longer.

Another thing to bear in mind when considering how long it will take to fix a roofing sheet is the weather. If it starts to rain, the contractors will probably have to stop and wait, as the roof will be too slippery to work on.

In general, it should take between 1 and 3 days to fit roofing sheets on a commercial property. If you’re not having a full roof replacement, it may only take one day, whereas a completely new metal roof could take up to 3 days.

Fibreglass, or GRP, flat roofs are very durable and should last you years, but over time they can become brittle and you might see some cracks or holes forming. Luckily, you can repair a fibreglass flat roof and it doesn’t have to be too difficult. Cracks in a fibreglass flat roof If you notice long cracks in your fibreglass roof, you can often use a fibreglass crack sealant. Simply clean the area, squeeze the sealant into the crack, then smooth it off. If you want it to look neater, you could coat the entire roof with a restorative coating which will make it look new again. Hole in a fibreglass roof If you notice a hole in your fibreglass flat roof, you’ll want to get this repaired as soon as possible to avoid any rainwater getting into your home. There are lots of fibreglass roof hole repair kits on the market, both online and in DIY stores, so you shouldn’t have trouble picking one up. They usually contain a mouldable UV cured patch that you can stick onto the hole. It will harden and become instantly weatherproof, so is the perfect emergency repair solution. Fixing pin holes in a fibreglass flat roof Unfortunately, if you find pin holes in a fibreglass flat roof it’s often because the installer didn’t use enough resin during the fibreglassing process. Luckily, if you can’t get back in touch with the installer or you only notice after a few years, you can fix this yourself. Sand down the roof back to the clear resin layer. Clean the entire roof with acetone and reapply some GRP roofing resin. Ensure that all the pinholes are filled – you might need two coats.