Find a Roofer you can trust in Marianglas.

Tar and gravel flat roofs are popular because the gravel weighs down the surface of the roof so it doesn’t blow away and it also protects it from sun damage. The tar makes the roof watertight, so you won’t get any leaks. However, sometimes problems occur and you’ll get cracks and leaks. So how do you repair a tar and gravel flat roof?

If you notice leaking coming through your flat roof, try to find the source of the leak. Since water can travel easily, it might not be where you think it is. The first place to check is the flashing, then any parts of the roof with gravel missing. Once you’ve found the crack, sweep away any remaining gravel and clean the area.

Apply a primer to the area and allow it to dry. Then, apply a tar and gravel roof patch that you can get from most DIY shops. Patch 2-3 inches around the damaged area, creating layers, and ensuring that there aren’t any air bubbles or gaps. Then you should cover the entire patch with gravel.

Before you try to repair a tar and gravel flat roof yourself, consider how much of the roof needs repairing. Professionals often say that if cracks and faults make up 25% or more of the roof, then you should look to replace it. It might be tempting to try and replace your tar and gravel roof yourself, but it’s best left to the specialists. They will ensure that your new roof is watertight and strong enough to withstand sun damage and storms.

How much a flat roof costs to repair depends on a few factors. Is your flat roof on a garage or an extension? What is the flat roof made from? It’s always best to get a few quotes to compare prices, but we’ll give you a rough idea here. If your flat roof was installed in the 1990s or earlier, it’s likely that you’ll see some leaks or damage soon. Felt flat roofs used to be installed completely flat, which meant that water couldn’t run off. That means that water pools and can create moss and damp. Sun exposure can also damage the felt, causing damage and eventually holes that lead to leaks. If you’re lucky enough to have got away with just needing a flat roof repair, this should set you back an average of £100 per square metre. If your roof is sagging due to the weight of it putting pressure on the timber frame, you might need additional joists – which could cost anywhere between £1,000 and £2,000, depending on how many you need. But if the problem is due to the internal part of the roof system becoming waterlogged, you could be looking at over £5,000. If your roof is severely leaking or the timber joists are rotting, it might be more cost effective to replace your flat roof. If you keep forking out for repairs, it will eventually be cheaper just to replace the whole thing, which could cost around £2,000.

Do You Need Felt Under Roof Tiles?

Before now, roofing felt were mainly incorporated to serve as a temporary waterproof roof on a building which would later on be changed for the permanent solid tiles or slate roof. This is due to the fact that rebuilding a roof can be time consuming taking a few number of days, the roofing felt would be used to protect the structure as well as the property it contains by acting as a barrier between the house and the harsh elements such as rain, wind, snow, sleet and more, while also providing minimal insulation until the structure is complete.

However those are in the olden days, in recent times, roofing felt ( also referred to as breathable roofing membrane or breathable felt) is now being used to create a safe and waterproof roof which is long lasting and will protect your house, properties as well as other outbuildings for a long period of time while also complying with the Building Regulations. So to answer the question - yes, you’re going to need felt under roof tiles as it has been made mandatory by building regulations.

Now let’s take a look at the different functions served by felt.

✓ You’ll need felt under roof tiles to prevent the roof space from being exposed.

✓ Roofing felt protects homes where a roof has not yet been installed to serve as a temporary protective layer against the elements.

✓ Roofing felt is particularly crucial for modern homes which are constructed to be more energy efficient and work to hold warm air from escaping the house. This is great to reduce your heating bills while also keeping both you and your loved ones cosy all throughout the year.

✓ Overall, building regulations imply that an underlay underneath the slate or tiles is now a compulsory requirement.

How Much Are Roof Tiles?

The way your roof looks speak volumes about your home or property. When you have an attractive roof installed, you give a huge impression of how beautiful the interior of your house is.

Roof tiles are the prefect roofing material if you wish to have your house looking elegant and decent. However, what turns off most homeowners about roof tiles is the belief that the prices are not budget friendly. This is absolutely false and in this article, we’re going to give you a rough estimate of the cost of roof tiles.

The price of roof tiles includes the cost of removing and getting rid of the old roofing materials, the cost of purchasing new roof tiles in the market as well as the cost of installing them on your house. There are a plethora of factors that affects the cost of roof tiles. These factors include the height and size of the roof, the roof’s design, the roof’s pitch, incidental costs of labour, the company hired as well as your location. What’s more? A roof with a complicated design such as hips and valleys will also generally cost more than simpler ones. Also, if you happen to reside in a place like London with higher cost of living and greater demand, the cost is also likely to be higher than other regions. As a result, providing an accurate cost of roof tiles is simply not possible.

Generally, the cost of having an entire roof retiled will cost within the range of £10,000 to about £20,000. For a more accurate estimate, you’ll have to identify reputable roofing professionals within your local area and find the roof tile prices that perfectly suits your budget.

In general, no – you don’t need planning permission for a Velux window. The Planning Portal says that you don’t need to apply for planning permission to install a roof window if the following conditions are met:

• A roof window must not protrude more than 150 millimetres above the existing roof plane
No roof window or any other alteration can be higher than the highest part of the roof or stand out above the roof ridge
• Side-facing windows must have obscure glazing to protect privacy of neighbours and, if they open, they must be 1.7 metres above the floor of the room in which they are installed

You don’t need to apply for planning permission for a roof window because they are covered under permitted development rights. However, if you’re a leaseholder or you live in a building where your local authority has made an Article 4 Direction, you will have to apply. Usually, an Article 4 Direction is made when you live in a conservation area where any external home improvements could affect the character and look of the area. Luckily, there are special Velux windows that are designed to be more likely to be accepted by your local planning authority. They’re called conservation windows and, although there’s still no guarantee that they will be accepted, they are designed to look more traditional. Even if you don’t need planning permission for your roof window, you still need to follow any relevant building regulations for your local authority. The most important parts for Velux windows are section J and section L of building regulations, which refer to energy efficiency, thermal insulation and fire protection.

How you install commercial rubber roofing is similar to fitting it on a residential property, except that the area that’s covered is likely to be bigger. With commercial properties, you should always leave any maintenance and repair works to the professionals – whether you own or lease the property, you could invalidate any insurance if you try to install rubber roofing yourself. We’ll outline the steps roofers will take when installing rubber roofing on a commercial property.

Firstly, the installers will remove any existing coverings and clean and dry the surface thoroughly. This is vital in ensuring that the rubber will stick. They will then unwrap the EDPM rubber membrane and leave it to rest until it’s fully expanded. On a warm day this may take around half an hour.

Next, the roofers will work with half a sheet of rubber at a time and adhere it to the roof surface. They may use a water-based adhesive which they will spread onto the roof in sections, then roll the membrane onto the surface before moving onto the next section. If they’re using a bonded adhesive, they will apply it to both the roof and the rubber and leave it to dry until it’s tacky before extending the membrane.

Once the EDPM rubber is rolled out, the installers will brush the surface with a large broom to get rid of bubbles and provide a stronger bond. Then they will work of the edges, applying adhesive to roof and walls edges, sealing corners and creating watertight seals. They’ll also tidy up any excess membrane and seal all the trims.

As long as it’s installed correctly, your commercial rubber roofing should last you decades without any repairs needed. It’s always best to inspect your roof regularly to spot any damage before it becomes a bigger problem.

It’s relatively simple to remove a Velux window, whether it’s Velux-branded or is another brand of roof window. Here is a breakdown of the steps you’ll need to take to remove a roof window:

1. Remove the sash (opening part) from the roof window frame. Usually there are screws in the hinges to loosen or a button to press and lift out.
2. Next, remove the tiles or slates from around the window frame along with the flashing.
3. Unscrew all the brackets around the window frame and lift out the frame.

It’s that simple! You can do all of this from inside your home – there's no need to climb on the roof. Removing the glass pane from a Velux window, for example if it has blown, is a more difficult job and should be left to a professional. It involves removing the sash from the roof window frame and then removing the surrounding parts of the sash to lift out the sealed unit. They will then place the new glazed unit into the sash frame before securing all the parts back onto the sash and fitting it back into the roof window frame.