Find a Roofer you can trust in Hessle.

As long as you can access them safely, it’s fairly easy to clean soffits and fascias. Using a sponge and warm water to scrub them is a good way to get off most types of dirt. You might want to add detergent or bleach to the water to make it more effective.

Once you’ve scrubbed your soffits and fascias, rinse them with clean water to make sure you’ve got all of the dirt and detergent off.

One of the most popular choices for roofing materials are roof slates. There is a number of advantages that a roof slate has, hey can be aesthetically pleasing, they can also increase the potential selling value of the house and many more. Slate is a sturdy and resilient material that delivers waterproofing physical characteristics to a pitched roof. Unlike other roof materials which absorb water slates do not. Therefore, slate is the most resistant towards freezing and water damage.

Find out the pitch of your roof

Before beginning with the fitting procedure, you need to figure out the pitch of your roof. The roof pitch commands how much overlap is essential with each slate. This has been made a lot easier than the early days with the advancement of technology.

Find out the required overlap

Once you’ve found out the exact pitch of your roof accurately, take a look at the slate producer’s description. Each manufacturer will propose the obligatory overlap in order to form a firm and safe slate roof.

Roll out the roof membrane

Firstly, guarantee your joists or trusses are clean of any sheards or old nails that could harm the membrane. You will now have to roll the chosen roofing membrane along the roof trusses. It is always wise to start from one of the bottom corners and keep rolling it along to the other corner.

Secure the roof membrane

Once the membrane has been moved out, use thump nails to protect one edge. You will now have to pull the membrane taut and carefully fix it into position. Do this before adding any nails across the membrane at points of intersection with the trusses for extra stability.

Batten placement

This is done to find the proper assignment of the battens. For this, you will need two full-sized slates along with an under eaves slate. Carefully position the battens on the top of the roof on the top of the overlay. Make sure not to fix them down since it will be easier to move them around and make any adjustments.

Why Do Roof Tiles Slip?

Despite being our first line of defence against the elements and covering the most valuable assets we possess, it’s shocking the reason why most roofs go unnoticed for years. However, when a damp patch suddenly appears on the ceiling or water starts to leak into our home, the condition of our roofing suddenly becomes of huge importance to homeowners.

In the UK, we get a fair share of harsh wind and heavy rainfall across the year which over time can lead to a plethora of roofing issues. One of the most obvious to identify is when roof tiles slip. If you’re also facing the same challenge, then you’ll most likely be interested in knowing the reason behind this occurrence. In this article, we’re going to take a look at some of the reasons why roof tiles slip.

Roof tiles can slip as a result of a corrosion of the nails that’s in place to secure your tiles to your roof. This happens especially during strong storms, whereby several roof tiles can be dislodged by rain and winds. If the affected tiles are just a few, then it may actually be a little issue to resolve. However, there are also times that the tiles slippage can be caused by a more serious issue. What’s more? You can also discover slipped roof tiles if the wood of your roof is corroded or weak. However, this applies a lot more to older homes than new or recent constructions. Any of the above reasons may be the main cause of your roof tiles slippage, but if you really want to know the exact cause for sure, you’ll have to call in a professional roof company to inspect your home.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

How much a flat roof costs to repair depends on a few factors. Is your flat roof on a garage or an extension? What is the flat roof made from? It’s always best to get a few quotes to compare prices, but we’ll give you a rough idea here. If your flat roof was installed in the 1990s or earlier, it’s likely that you’ll see some leaks or damage soon. Felt flat roofs used to be installed completely flat, which meant that water couldn’t run off. That means that water pools and can create moss and damp. Sun exposure can also damage the felt, causing damage and eventually holes that lead to leaks. If you’re lucky enough to have got away with just needing a flat roof repair, this should set you back an average of £100 per square metre. If your roof is sagging due to the weight of it putting pressure on the timber frame, you might need additional joists – which could cost anywhere between £1,000 and £2,000, depending on how many you need. But if the problem is due to the internal part of the roof system becoming waterlogged, you could be looking at over £5,000. If your roof is severely leaking or the timber joists are rotting, it might be more cost effective to replace your flat roof. If you keep forking out for repairs, it will eventually be cheaper just to replace the whole thing, which could cost around £2,000.

How Much To Replace A Flat Roof

There’s no straight answer to this question. However, the average cost lies within the range of £1000 to £5000. This range may look too wide but the price is greatly influenced by a number of factors which is capable of making the price increase or decrease. Some of the factors affecting the cost of flat roof coverings and replacement include: the type of flat roofing system and materials you want, the area size of the flat roof in M2, the project’s location, the roofing company to be used, the ease at which to reach the roof, cost of removing the old flat roof as well as cost of removing the other waste.

Although there are many factors to be put into consideration but the most crucial factor is the size of the house or the area size of the flat roof in M2. for instance, a one bedroom apartment’s flat roof will have a price between £1500 to £3000. This is, however, with the assumption that the flat roof is going to be used as the main roof of the house. But if you’re only using it for a section of the house like your garage, the price could range between £700 to £1000

There four commonly used types of flat roof materials which includes fibreglass, felt, rubber and lead. If you need a felt roof, for example, the price is between £40 to £70 per m2. And in the same tone, a metal roof will generally cost more than a a flat roof made from rubber.

Another important factor we’ll discuss is the labour or the roofing company to be used. Different roofing companies will charge different prices. As a result, you should carefully compare the prices of the companies in order to get a great deal.

How To Identify Asbestos Roof Tiles

Found in some particular rocks, asbestos is a naturally occurring mineral that’s commonly used before the 1990’s as a building material specifically for roofing. This material was banned in the UK as it was discovered to possess harmful fibres which is potentially dangerous to human’s respiratory health when disturbed and inhaled. According to several reports this health conditions include non cancerous lung disease, mesothelioma and asbestosis, which are all untreatable. Therefore, be it in a domestic or industrial setting, there’s the need to know how to identify asbestos and if found, start the removal process as quickly as possible.

While the three types of asbestos used in roof tiles can be quite easy to identify by themselves, a total reverse is the case, when mixed into a tile. Generally roofing tiles that includes asbestos will mostly have colours such as grey, white or blue-white colour, but so does several other roof tiles made from other materials that are totally safe. As a result, the only way in which you can identify if a tile contains asbestos is by looking for an identification mark. These marks are mostly inscribed onto about one in twenty tiles, therefore if you have a strong feeling that your roof tiles contains asbestos, you may have to remove several tiles before you can identify the marked one. Otherwise, the only way you can confirm is by sending a sample to a certified asbestos testing lab. These labs are knowledgeable and possess the right equipment, tools as well as testing kits to determine the levels of asbestos in your premises. With this, you have a better chance of getting quality results than any other means. What’s more? They’ll also recommend expert asbestos removal services if the harmful material is found to be present in your house.

Ponding is where you see pools of water appearing on your flat roof. Unless your roof is leaking or showing other signs of damage, you don’t need to replace it. When you do have your flat roof replaced, tell the contractor so they can find out the cause of the ponding.