Find a Roofer you can trust in Ellesmere Port.

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.

Do You Need Felt Under Roof Tiles?

Before now, roofing felt were mainly incorporated to serve as a temporary waterproof roof on a building which would later on be changed for the permanent solid tiles or slate roof. This is due to the fact that rebuilding a roof can be time consuming taking a few number of days, the roofing felt would be used to protect the structure as well as the property it contains by acting as a barrier between the house and the harsh elements such as rain, wind, snow, sleet and more, while also providing minimal insulation until the structure is complete.

However those are in the olden days, in recent times, roofing felt ( also referred to as breathable roofing membrane or breathable felt) is now being used to create a safe and waterproof roof which is long lasting and will protect your house, properties as well as other outbuildings for a long period of time while also complying with the Building Regulations. So to answer the question - yes, you’re going to need felt under roof tiles as it has been made mandatory by building regulations.

Now let’s take a look at the different functions served by felt.

✓ You’ll need felt under roof tiles to prevent the roof space from being exposed.

✓ Roofing felt protects homes where a roof has not yet been installed to serve as a temporary protective layer against the elements.

✓ Roofing felt is particularly crucial for modern homes which are constructed to be more energy efficient and work to hold warm air from escaping the house. This is great to reduce your heating bills while also keeping both you and your loved ones cosy all throughout the year.

✓ Overall, building regulations imply that an underlay underneath the slate or tiles is now a compulsory requirement.

How Much To Replace A Flat Roof

There’s no straight answer to this question. However, the average cost lies within the range of £1000 to £5000. This range may look too wide but the price is greatly influenced by a number of factors which is capable of making the price increase or decrease. Some of the factors affecting the cost of flat roof coverings and replacement include: the type of flat roofing system and materials you want, the area size of the flat roof in M2, the project’s location, the roofing company to be used, the ease at which to reach the roof, cost of removing the old flat roof as well as cost of removing the other waste.

Although there are many factors to be put into consideration but the most crucial factor is the size of the house or the area size of the flat roof in M2. for instance, a one bedroom apartment’s flat roof will have a price between £1500 to £3000. This is, however, with the assumption that the flat roof is going to be used as the main roof of the house. But if you’re only using it for a section of the house like your garage, the price could range between £700 to £1000

There four commonly used types of flat roof materials which includes fibreglass, felt, rubber and lead. If you need a felt roof, for example, the price is between £40 to £70 per m2. And in the same tone, a metal roof will generally cost more than a a flat roof made from rubber.

Another important factor we’ll discuss is the labour or the roofing company to be used. Different roofing companies will charge different prices. As a result, you should carefully compare the prices of the companies in order to get a great deal.

How To Clean Concrete Roof Tiles

Dirt, moss and algae usually sees concrete roof tiles as the perfect place to reside. They can damage the structural bonds of your roof, they can lead to overheating of the attic and roof space as well as blocked gutters. In order to protect the structural integrity of your roof and ensure your home and properties are well protected against the elements, it’s therefore crucial to clean your roof regularly. There are plethora of ways to go about this but which method will best suit your concrete roof tile?

When it comes to working at heights, skill and confidence is paramount even if the actually cleaning and maintenance happens to be an easy task. As a result, if you lack the two attributes mentioned, we’d strongly recommend that you call in a professional roof cleaning contractor who can guarantee the best results for help. In this article, we aim to give you a good insight into the concrete roof tiles cleaning process. Let’s have a look!

✓ Use a trowel or stiff brush

This is a manual method which involves scraping off the algae, moss and dirt by hand using an effective tool like a trowel. However, before you do this make sure its a very dry day. Also, you can make use of a stiff brush to scrape off the dirt. Both cleaning tools are very easy and effective means to clean concrete roof tiles.

✓ Use chemicals

You can apply fungicide, moss killers and anti moss treatments with the help of a spray to kill any plant life on your concrete roof tiles. However, you should only do this after you’ve successfully scraped the surface with a trowel or a stiff brush.

How to repair a hole in a flat roof depends on what material your flat roof is made from. If you have an asphalt, felt or EDPM rubber roof, the repairs are quite simple, whereas it’s a bit more tricky if you have a fibreglass flat roof. How to repair a hole in an asphalt flat roof If you’ve got a small hole in your asphalt flat roof, you might get away with using a paint-on fix from a tin. It’s best to use this as a temporary measure to tide you over until you can get in touch with a professional. If the hole is on the flashing, you can add heat-applied flashing tape to it, or use a patch of torched-on roofing felt. There are liquid systems you can use, but usually they’re only available to the trade. Repairing a hole in a felt flat roof It's a similar process to asphalt roofing if you want to repair a hole in a felt flat roof. Use a paint-on fix for a temporary solution, but the best way to repair a hole is to use a torched-on piece of roofing felt to cover the hole and make it watertight again. How to fix a hole in an EDPM rubber flat roof If the hole in a rubber flat roof is small, you may be able to get away with applying some lap sealant to the hole. Only use a small amount, as if you go for a more permanent repair later down the line all of this will need to be scraped off. You can also use a malleable piece of self-adhesive flashing – clean the area, add EDPM primer and stick the patch on from the centre outwards. Add sealant to the edges if you want to give it more water protection. How to fix pin holes in a fibreglass flat roof If you find pin holes in your fibreglass roof, it usually means there wasn’t enough resin used at installation. To repair the holes, you’ll need to sand down the entire roof back to the clear resin. Then clean the area with acetone and apply GRP roofing resin – the acetone ensures that the resin sticks. You might need two coats of resin to get rid of all the holes.

What Is The Average Cost To Replace A Flat Roof?

Are you interested in knowing how much it costs to replace a flat roof? Here, you’ll discover a price breakdown for replacing flat roof. This includes a number of price determining factors such as materials costs as well as cost of labour and cost per square metre. All these enables you to make easy calculations so that you can determine a flat roof replacement estimate for your own project.

The type of flat roof that is the most common type is the garage roof and for the replacement of a single garage roof, the cost will fall between the range of £700 to £1000. Meanwhile for a double garage, you should expect a price increase of about 40 percent to 50 percent. The main price determinant that’s affecting the price of a new flat roof is the material incorporated in making it. For instance, lead or fibreglass are much more expensive when compared to felt roofs.

Generally, the cost of a flat roof replacement will fall within the range of £700 to £1300 varying largely due to the type of materials to be used by the roofer, the roof’s size as well as whether or not scaffolding would be used. Multiple flat roof applications also comes with different costs which includes:

• Felt roof ( £40 to £60 per square metre).

• Fibreglass roof ( £70to £90 per square metre ).

• Rubber roof ( £80 to £85 per square metre ).

• Lead bay roof ( £90 to £105 per square metre ).

• Fibreglass bay roof ( £40 to £60 per square metre ).

Several professional roofers work in pairs and to hire them you’re likely to be charged between £200 to £300 per day. The project can be completed with just a day’s work, but the installer should be back to make sure there are no leaks.

Chimneys are certainly on top of the commonly overlooked features when it comes to cleaning a house. This is quite understandable given the fact that they’re not readily accessible and not in plain sight, hence, home and property owners tend to overlook the relevance of any chimney cleaning effort. But this can be a grave mistake! The importance of having your chimney swept on a regular basis cannot be over emphasized and even more so if it happens to be on a wood burner. Not only can a dirty chimney constitute fire hazard, but when left uncleaned it can also give rise to blockages which can lead to carbon monoxide poisoning. In fact, from 2014 to 2018, one of the top factors contributing to about 25% of home heating fires is due to lack of cleaning, mainly from solid-fueled heating equipment, mostly chimneys. Therefore, sweeping your chimney regularly is a safety precaution and when they happen to be on a wood burner, this exercise becomes a lot more important. With that in mind, the question that arises is just how often is sweeping of a chimney on a would burner needed?

Well, it’s strongly advisable to sweep chimney on a wood burner at least twice a year by a qualified professional depending on the usage. If you happen to own an oil burning fireplace, the same also applies. In other words, this means that regardless of the type of chimney you possess, the cleaning must be done regularly. However, most chimney would only need to be swept once in a year by a qualified professional.