Find a Roofer you can trust in Brecon.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Chimney liners are a very important component of the chimney, but the fact is most home and property owners either continue to overlook them or aren’t even aware of their existence. This is, however, quite understandable given the fact that they usually last a long period of time – more than 50 years. To ensure that they last that long, the question that arises is, do chimney liners need to be swept and cleaned? The short and simple answer to this question is yes, chimney liners definitely needs to be cleaned on a frequent basis. A chimney liner happens to be an essential part of your chimney. When it’s not cleaned, it tends to accumulate dust, soot and dirt which can give rise to a number of problems you’d rather want to avoid. Chimney liner are able to provide adequate protection to your flue but even at that the water, creosote and other contaminant build up can make the liner to deteriorate, and making it unsafe for usage. In other words, contrary to several belief, chimney liners do need the same amount of cleaning as chimneys without liners. Failure to sweep your chimney liners can give rise to the following problems:

• Creosote buildup. If your main source of fire is wood, then you’ll definitely have creosote present in your chimney. This is highly combustible and its buildup may lead to fire outbreak.
• Carbon monoxide poisoning. Carbon monoxide is said to be on the rise by NCBI and its primarily generated from heating systems which are terribly ventilated as a result of uncleaned or dirty chimneys.

How To Clean Algae Off Roof Shingles

Stains and dirt on asphalt shingles can only make your entire house look shabby which can go a long way to hide away the true value of your building. In some cases, dirts and stains on asphalt roofing shingles are nothing more than a cosmetic issue. However, there are also times in which it goes far beyond this - when the stains are indicators of a problem that if ignored, can result in a serious roof damage and ultimately, roof failure. In most cases, it’s usually hard to distinguish these stains and hence, the more reason why your asphalt roofing shingles should be regularly cleaned and maintained. In this article, we’re going to look at how you can get rid of algae of your roof shingles.

Algae growth on roof usually have either blue, green or black stains. They normally begin with little spots which will develop into streaks overtime. These stains are mostly mistaken for moss or mildew and aren’t harmful to any other thing than the roof shingles. However, the look it gives the entire house is something nobody enjoys.

It should be noted that this is a task that deals with working at height and requires skills and confidence to pull off. If you lack any of these qualities, simply reach out to a professional for help.

✓ Safety first. Put on protective clothing.

✓ Apply a bleach solution with a garden sprayer and let it sit for up to 20 minutes

✓ Rinse the roof thereafter with the stream from the hose (do not use a pressure washer as it can damage the roof shingles)

✓ If there are still algae left after rinsing with water, you can make use of a brush with medium-stiff bristles to gently scrub the stains off. If some stains are still left, simply let the roof dry before repeating the process again.

Strong winds can cause extensive damage to unprotected rooftops and in fact tiles act as very suitable protection. The extra weight they provide is great at countering high wind loads and if anything is damaged during severe weather, replacing tiles is straight forward for professional roofers.When you compare this to lightweight materials there’s a significant difference. If you wish to have extra protection, experts recommended having sarking fitted.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

How To Replace Roof Tiles

If your roof tiles is cracked, missing or damaged in one form or the other, you may want to read up to see if the replacement is something you can do by yourself. The answer is yes, roof tiles replacement can be done as a DIY project especially if you’re an experienced DIYer or confident enough to tackle the project. However, if you lack the confidence needed to take on this task, then we’d strongly recommend you get in touch with a professional roofer who can guarantee the best results for help. In this article, we’ll show you how you can replace your roof tiles with relative ease. Let’s take a look!

✓ As you would have rightly guessed, the first step to replacing your roof tiles is to remove the existing damaged roof tile to create space for the new tile. In the event whereby the roof tile is nailed to down, you will have to pry the nails off before proceeding with the broken tile removal.

✓ Once the damaged tile has been removed, the next step is to replace the roof tile as there’ll now be a gap in the roofing area. Simply position the new tile rightly into the space that was formerly filled by the old damaged tile.

✓ After successfully placing the new tiles in spot of the removed tile, you’ll now have to replace the overlapping tiles to their correct position to secure them. To this with a hammer to lift the overlapping tiles a little bit, so you can pull them back into the appropriate place.

✓ This final step is not a necessary one. However, if you’d like to secure your roof tiles further, you can simply nail it into place with a hammer.

Tar and gravel flat roofs are popular because the gravel weighs down the surface of the roof so it doesn’t blow away and it also protects it from sun damage. The tar makes the roof watertight, so you won’t get any leaks. However, sometimes problems occur and you’ll get cracks and leaks. So how do you repair a tar and gravel flat roof?

If you notice leaking coming through your flat roof, try to find the source of the leak. Since water can travel easily, it might not be where you think it is. The first place to check is the flashing, then any parts of the roof with gravel missing. Once you’ve found the crack, sweep away any remaining gravel and clean the area.

Apply a primer to the area and allow it to dry. Then, apply a tar and gravel roof patch that you can get from most DIY shops. Patch 2-3 inches around the damaged area, creating layers, and ensuring that there aren’t any air bubbles or gaps. Then you should cover the entire patch with gravel.

Before you try to repair a tar and gravel flat roof yourself, consider how much of the roof needs repairing. Professionals often say that if cracks and faults make up 25% or more of the roof, then you should look to replace it. It might be tempting to try and replace your tar and gravel roof yourself, but it’s best left to the specialists. They will ensure that your new roof is watertight and strong enough to withstand sun damage and storms.