Find a Roofer you can trust in Bishops Castle.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

An eave is the edge of a roof, which is why they are now and then called roof eaves. On a household's outside, eaves can stick out outside the side of the building, serving both ornamental and applied purposes. The eave of a house has come to mean the lower area of the roof that projects after the external covering, as opposite to a cornice, which is part of the entablature in Classical architecture.

Think of how a roof outspreads outside the covering, and then think about how a hard rain may roll down the roof and, on the ground, away from the structure. Centuries ago, the eavesdrop was that indentation line made around a structure when the rain fell off the edge of the roof onto the ground.

Types of Eaves

A roof can come to a conclusion in essentially three ways. A closed eave is the one which has very little or no overhang at all. An open eave has a visible overhang, projecting beyond the roof brackets. A boxed eave is surrounded with a soffit.

The Use of Eaves?

An eave can defend the siding and substance of a structure. A roof eave bulging beyond the sides permits snow and rain to fall from the roof away from the covering, to the ground. The more the "weather" gets thrown away from the household, the chances of you having a dry basement increases.

In cases of regions with a warmer climate, a large eave can help provide shade to the interior of the house. In rainy environments, the prolonged eaves of Asian architecture deliver shelter from the climate, as well as direction. In the 21st century, an eave may be an inconspicuous site for security cameras and light.

Fibreglass, or GRP, flat roofs are very durable and should last you years, but over time they can become brittle and you might see some cracks or holes forming. Luckily, you can repair a fibreglass flat roof and it doesn’t have to be too difficult. Cracks in a fibreglass flat roof If you notice long cracks in your fibreglass roof, you can often use a fibreglass crack sealant. Simply clean the area, squeeze the sealant into the crack, then smooth it off. If you want it to look neater, you could coat the entire roof with a restorative coating which will make it look new again. Hole in a fibreglass roof If you notice a hole in your fibreglass flat roof, you’ll want to get this repaired as soon as possible to avoid any rainwater getting into your home. There are lots of fibreglass roof hole repair kits on the market, both online and in DIY stores, so you shouldn’t have trouble picking one up. They usually contain a mouldable UV cured patch that you can stick onto the hole. It will harden and become instantly weatherproof, so is the perfect emergency repair solution. Fixing pin holes in a fibreglass flat roof Unfortunately, if you find pin holes in a fibreglass flat roof it’s often because the installer didn’t use enough resin during the fibreglassing process. Luckily, if you can’t get back in touch with the installer or you only notice after a few years, you can fix this yourself. Sand down the roof back to the clear resin layer. Clean the entire roof with acetone and reapply some GRP roofing resin. Ensure that all the pinholes are filled – you might need two coats.

Clean of your conservatory gutter is probably not one of the most enjoyable chores you’d like to take on around the house. Not only is it messy and tedious, but it’s also time consuming and smelly. It’s a job every home and property owner would rather avoid, but unfortunately everyone has to do it. It’s a necessity due to the fact that neglect gutters holds and harbours mould, moss as well as plant debris. It would have been better if this is only disgusting, but the actual truth is that should be the least of your worries as this gradual build up of organic material in your conservatory gutters can minimize their drainage abilities, leading to leakages and spills that can damage your conservatory.

Cleaning of your conservatory gutter is a task that can be done regardless of your level of experience. However, it’s advisable to call in a professional for help especially if you lack the confidence required to pull it off.

• Use a ladder for a closer look. Cleaning your gutters from the ground by poking it with a hooked tool might seem the best way out, but in truth you risk damaging the gutters or brackets and marking the conservatory panes when you don’t see what you’re doing.
• Invest in specialist tools. For expert DIYers, taking off your downpipes from the wall to clean might be a pretty easy task. However, for most people it can be extremely frustrating. As a result, there’s the need to get hold of some flexible gutter brushes. With a bendable stem and stiff bristles, these are able to hook and dislodge dirt and leaves inside your downpipes with relative ease.

Velux windows, or roof windows, are very easy to clean. Regular cleaning helps to keep them looking bright and shiny for years to come. So how should you clean Velux windows?

If you want to clean the air filter, you can remove it and wash it with your normal household cleaners. Velux windows have a cleaning position, so rotate and secure it into this position then remove the filter. You should be able to buy new filters from the manufacturer of your roof window.

To clean the outer pane, there’s no need to lean out of the window and risk falling out. Simply rotate the sash (the opening part) 180 degrees and secure it into position. Then you can clean the pane with a soft, lint-free cloth, sponge or squeegee and clean water. If you live in a hard water area, add some detergent to the water and wipe the window dry when you’re finished. You can also use normal non-abrasive household cleaners.

It’s recommended that you clean the flashing around your roof window at least once a year. You can use a brush to do this. This will allow rainwater to flow freely and stop any leaves from collecting.

If you’re in any doubt about using certain cleaners on your Velux windows, get in touch with the manufacturer who should be able to help. You can also do a patch test on an inconspicuous area if you’re unsure.

In the UK, fireplaces are a very common addition to homes and property and reasonably so. Not only do they represent a great source of heat, but they’re also quite timeless in their beauty, thereby adding more value to your property. Now every fireplace possesses some sort of chimney, asides from the ones that are ventless. And while you might not be aware, every chimney poses a number of dangers which includes being a fire hazard and can also lead to carbon monoxide poisoning as a result of improper or lack maintenance.

Since your chimney will be clogged up over time with all sorts of soot and often cleaned from the top of the roof, cleaning of a chimney comes with a huge amount of risk. As a result, you run the risk of falling off if you decide to clean one by yourself. And even if you’re the type that’s comfortable being on high level places, you should know cleaning a chimney is not the most pleasant of jobs. It can be quite messy as accumulated creosote and soot can drop into your home causing a cloud which covers both the floor, furniture and any other thing you have in the room. Furthermore, chimney cleaning requires specialized skills and knowledge which professionals have acquired after several practices. For instance, missing out on a spot can result in an unchecked chimney fire or a masonry crack.

The simple answer to this question is, therefore, a big NO - you should leave the cleaning to the professionals.  Professionals are not just limited to chimney cleaning; they’re trained to identify any structural issues while also being able to carry out a close analysis of the chimney. They’ll fix minor issues on site and give you a peace mind for any future wood burning activities.

The roof is a particularly important part of the home, providing weather and water protection. Therefore, it’s important to regularly check your guttering system and clean out any debris that could cause blockages.Advice given is to consider having a mesh gutter guard to prevent the build-up of leaves and other debris, especially if you want to harvest rainwater.