Find a Roofer you can trust in Sunderland.

While it sounds like it could be difficult to plasterboard around a Velux window, it needn’t be. As long as you have the right tools and materials, you should be able to plasterboard around your roof window easily and make good ready to be skimmed. When you or a tradesperson has fitted your Velux window into your roof, you’ll probably need to plasterboard over it to create a good ceiling. To do this, you’ll need:

• Plasterboard sheets – make sure you measure your room so you know how much you’ll need
• Screws to secure the board in place
• Drill
• Hammer
• Straight edge and pen knife to score the board before trimming
• Fine toothed saw the cut the plasterboard

When you’re ready to plasterboard around your roof window, make sure you’ve cleared enough space to work in. Then you can begin by cutting your plasterboard to size using your straight edge and pen knife to score, then your saw to get a clean cut. A common way of plasterboarding around your Velux window is to use the groove on the window frame to hold one edge of the board, then screw the other edge to the battens on the ceiling. People often use drywall screws these days as they have a better grip of the plasterboard as they drive through. You’ll need to use a drill to screw these in. However, you could use plasterboard nails, which are galvanised to stop rusting. When you’ve done this, you can then skim the walls or ask a plasterer to do it for you. Plastering, while it looks easy, is a tricky skill so it’s always best to ask a professional to do it.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Chimney liners are a very important component of the chimney, but the fact is most home and property owners either continue to overlook them or aren’t even aware of their existence. This is, however, quite understandable given the fact that they usually last a long period of time – more than 50 years. To ensure that they last that long, the question that arises is, do chimney liners need to be swept and cleaned? The short and simple answer to this question is yes, chimney liners definitely needs to be cleaned on a frequent basis. A chimney liner happens to be an essential part of your chimney. When it’s not cleaned, it tends to accumulate dust, soot and dirt which can give rise to a number of problems you’d rather want to avoid. Chimney liner are able to provide adequate protection to your flue but even at that the water, creosote and other contaminant build up can make the liner to deteriorate, and making it unsafe for usage. In other words, contrary to several belief, chimney liners do need the same amount of cleaning as chimneys without liners. Failure to sweep your chimney liners can give rise to the following problems:

• Creosote buildup. If your main source of fire is wood, then you’ll definitely have creosote present in your chimney. This is highly combustible and its buildup may lead to fire outbreak.
• Carbon monoxide poisoning. Carbon monoxide is said to be on the rise by NCBI and its primarily generated from heating systems which are terribly ventilated as a result of uncleaned or dirty chimneys.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

It depends on the material you use, but if your flat roof is installed correctly it should last for at least 10 years, and at least 20 if a material other than felt is used. Always question a roofing company when they quote to find out what materials they use and what guarantee's they offer.

A leaky flat roof is one of those things every home and property owner would rather prefer to avoid. Not only can it be extremely frustrating to deal with, but it can also have a grave impact on the overall integrity and value of your property especially when things are not done properly. Generally, all leaky roofs pose serious problems, however, a leak in a flat roof is even a lot more complicated. Ranging from the quite simple repairs to the incredibly complex fixes, flat roof repair (also known as low slope roof repair) is be seriously problematic and at times, can call for a reconstruction which involves complicated roof insurance as well as an experienced professional support.

Flat roof repair consists of many different types. Cap sheet roofs possess layers of material glued together with hot asphalt, including a roll of mineral surface glue using asphalt to the top rather than gravel. The tar and gravel roofs also possess layers of material glued together with the help of hot asphalt, with the use of asphalt on top as well as gravel included in the asphalt. A modified bitumen roof possesses more strength when compared to a cap sheet roof or the conventional tar and gravel roof. This can be 2 or 3 plies, smooth or with a mineral surface, torched on, mopped on or self adhering. What’s more? A TPO roof is a single ply roof which is usually heat welded together. A PVC roof is also a single ply roof that’s heat welded together while an EPDM is a single ply roof that’s glued together. The foam roofs as well as various coatings are incorporated to reflect the sun’s UV rays and also to maintain and seal the roof.