Find a Roofer you can trust in Wigtownshire.

It can be a huge headache, but cleaning of gutters is a task that needs to be done and even more so when it’s a stained white gutter. Nobody want to do it, but everybody has to. If you happen to lack the required confidence to pull this off as it has to do with working at heights, then we’d strongly recommend that you get in touch with a reliable professional who can guarantee the best results for help and also save you some time and money from potential costly errors. In this post, we’re going to show you some of effective way in which you can tackle stained white gutters effectively.

Firstly, you’ll have to take out the ladder with a pair of rubber gloves. Simply position the ladder safely, climb up the roof and start removing the leaves and other debris clogging up the gutters. You can also make use of a garden trowel to remove the very thick debris. Once done, spray the gutter using a garden hose to flush out the dirt as this will make the stains visible. Then prior to cleaning, ensure to cover the plants or landscape underneath with tarp or plastic sheet since the cleaning solution may negatively impact the vegetation.

Start to clean by spraying an all-purpose cleaner on the stains and srub them off using a scrub brush. You can also try a mixture of 1/4 of water with 1 cup of bleach and 1 teaspoon of dish soap. Dip your scrub brush in this solution to scrub off the stains. The bleach mixture is guaranteed to eliminate any mold or mildew that growing on your gutters with ease.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

The feasibility of this will depend on the roof’s strength, in particular its load bearing capabilities. This is simply because tiles are heavier than the metal sheeting. Normally a tiled roof will need to take a load capacity of 60kg per square metre. You will need a trusted roofing company to advise on this.

You should inspect your roof twice a year, ideally after rain or snow, to see if it’s draining properly. Also in the Spring to check for damage that may of been caused over the winter months that will need to be put right before the next winter. Have an inspection carried out if you are unsure.

How long it takes to fix a roofing sheet on a commercial property will depend on the size of your roof and how difficult access is. Corrugated iron roofing sheets are much easier to fit than other roofing materials such as clay tiles or EDPM rubber, so that will work in your favour.

The size of the team of the roofing company you engage will also make a difference. If they have a lot of tradespeople working on your roof with lots of experience, it will take less time, while if there are only a couple of people it will take longer.

Another thing to bear in mind when considering how long it will take to fix a roofing sheet is the weather. If it starts to rain, the contractors will probably have to stop and wait, as the roof will be too slippery to work on.

In general, it should take between 1 and 3 days to fit roofing sheets on a commercial property. If you’re not having a full roof replacement, it may only take one day, whereas a completely new metal roof could take up to 3 days.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

Roofing is one of the most significant portions of your household. Not only does it protect the inhabitants from the elements, but it also plays a vital role in the architectural appeal. When people reflect of roofing, they consider various types of tile for the job.

Metal Tiles

When we talk of metal roofs, most of the people think of roofs made of metal panels which are joined together by joints or raised seams. This is often not the case as there are several numbers of obtainable metal roofing products.

Ceramic Tiles

Another popular choice of roofing material is ceramic. Clay tiles are incombustible and fairly sturdy, necessitating scarcer repairs or substitutions than asphalt roofs.

Concrete Tiles

For those that like the look of ceramic tiles, as well as their fire resistance, this may not be the choice, but those who want something a little tougher and less susceptible to cracking when having work done on the roof, there are the best tiles.

Bituminous Tiles

For those that want a lightweight, supple tile that’s easier to fit, there’s the bituminous tile. These types of tiles are made from cellulose fibre or using fibreglass allowing them to be flexible.

Polymer-Sand Tiles

A new-fangled substitute for ceramic tiles is the polymer-sand tile. Created from a combination of sand bound together with polymers, these are very rigid, sturdy tiles are shaped in a mould.

Copper Tile

Copper roofs can be a great choice for many due to their long lifespan. Copper tiles have the ability to last over a century before needing replacement.

Composite Tile

Another newer roofing tile is the composite. This is a multi-layered tile that is made using metal, acrylic and stone granules.

Stone Tiles

This is one of the oldest forms of roofing tiles that you can get out there. It is also one of the longest-lasting tiles on the market as well, with some roofs lasting well over 100 years.

An eave is the edge of a roof, which is why they are now and then called roof eaves. On a household's outside, eaves can stick out outside the side of the building, serving both ornamental and applied purposes. The eave of a house has come to mean the lower area of the roof that projects after the external covering, as opposite to a cornice, which is part of the entablature in Classical architecture.

Think of how a roof outspreads outside the covering, and then think about how a hard rain may roll down the roof and, on the ground, away from the structure. Centuries ago, the eavesdrop was that indentation line made around a structure when the rain fell off the edge of the roof onto the ground.

Types of Eaves

A roof can come to a conclusion in essentially three ways. A closed eave is the one which has very little or no overhang at all. An open eave has a visible overhang, projecting beyond the roof brackets. A boxed eave is surrounded with a soffit.

The Use of Eaves?

An eave can defend the siding and substance of a structure. A roof eave bulging beyond the sides permits snow and rain to fall from the roof away from the covering, to the ground. The more the "weather" gets thrown away from the household, the chances of you having a dry basement increases.

In cases of regions with a warmer climate, a large eave can help provide shade to the interior of the house. In rainy environments, the prolonged eaves of Asian architecture deliver shelter from the climate, as well as direction. In the 21st century, an eave may be an inconspicuous site for security cameras and light.