Find a Renewable Energy Specialist you can trust near you.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Tesla’s top-of-the-range battery storage system is still one of the most expensive on the market. It has a huge 13.5kWh usable capacity and can even keep you up and running during a power cut. But how long does a Tesla Powerwall battery last? And does this mean it’s worth investing in one?

The Tesla Powerwall 2.0 comes with a 10-year warranty. But Tesla says that it should last way beyond this – at least 5 years longer. The standard warranty says that it should work at 70% capacity for the full 10 years – so if it loses more than 30% of its storage capacity within that time, it should still be covered.

While the Tesla Powerwall does last a long time, it has a large capacity that most average households won’t require, and it’s a costly option. After installation, the Powerwall 2.0 will set you back between £6,500 and £9,000, so ideally you want it to last past its 10-year warranty.

Before you splash out, consider the size of the solar panel system you want to install or you already have. Will it generate enough electricity to make it worth storing in the Powerwall? If not, are you expecting to upgrade your solar panels to a larger system in the future? If you are, then it might be worth investing in a Powerwall. It might also be better to wait until you come to upgrade your solar panels – the solar battery price trend is going the same way as solar panels, so they will probably continue to decrease in price as more people adopt the technology.

There are two main types of air source heat pump: air-to-water and air-to-air. They work in different ways and have different advantages and disadvantages. Make sure you do your research so you know which one is best for you. Alternatively a registered installer will be able to determine the best type for your property.

You shouldn’t need to maintain your solar panels much at all as long as there’s nothing piled up on top of the panels that could block out the sun. They are installed at an angle, so when it rains the water runs off them and gives them a clean. However, if this doesn’t quite cut it, you can spray them with a hose a few times a year.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.

How Do Solar Panels And Batteries Work Together?

With solar panel system rapidly becoming an ubiquitous phenomenon within the modern society, several homeowners in the UK are just coming to terms with the numerous benefits offered by the system. The solar power’s popularity has even led to the rise of another renewable technology - solar batteries able to store excess solar power that can be used later. Now several companies such as Tesla are now building solar batteries that can be fitted alongside solar panels for your building. So how exactly do solar panels and batteries work together? Let’s have a look!

Solar panels make use of the sun light to generate electricity and as a result, they can’t function when sunlight is absent - giving a big issue of how to power your house when it’s dark. In the event whereby this occurs, you’re afforded two options which is either to contact energy providers to buy electricity or purchase a battery storage system.

So what’s the function of the battery storage system? Basically when your solar panel provides electricity which is not needed right away, a solar battery will work to convert the DC electricity into AC energy which is going to be stored for later use (when you actually need it). in other words, your solar panels charge the batteries when you do not require the energy they’re generating right away.

As a result, when it’s dark and the solar panels are no longer functioning, your system will tap into the energy that’s already been stored by your battery for later use. This way, you can be totally independent of the National Grid, which implies more savings on your electricity bills.