Wall Tiling in Feltham

How To Lay Wall Tiles

Laying of wall tiles is a task that should be done with great caution, especially if you’re working on a tight budget. It is guided by its own unique set of rules which you do not dare to break if you wish to get it right the first time, and also to avoid incurring some additional costs. If you do not have a proper training or experience, laying of wall tiles is better left to a skilled professional for the best possible outcome. However, this guide will walk you through the various steps in the process to help improve your knowledge. Let’s get started!

lPrepare The Wall Surface

• Make sure the surface is clean, dry and smooth

• In wet areas, wall tiles should be fitted over a backer board

• If it’s a painted wall, ensure to sand the surface before installation.

lCreate The Layout

• Locate the centre of the wall

• Create an intersecting vertical and horizontal layout lines using a level

• Ensure to include spaces for grout joints when creating the layout.

lApply The Adhesive

• For wet areas, makes use of thin-set adhesive that’s cement-based.

• For dry areas, you can use pre-mixed mastic adhesive

• Follow the manufacturer’s instruction to prepare the adhesive

• Using a notched trowel, apply the adhesive (hold the trowel at about 45 degrees angle)

• Ensure not to cover the layout lines with the adhesive

lInstall The Tiles

• Follow the layout lines to install the wall tiles

• Place the full tiles firmly on the adhesive and twist slight and gently to make them fit.

• Use tile spacers to ensure constant gaps for grout joints.

lCut The Tiles

• After installation of the full tiles, there’ll most likely be a need to cut some tiles to fit.

• Cut the tiles with a wet saw or manual tile cutter

lGrout The Tile

• Ensure the adhesive is well dried and remove the tile spacers.

• Prepare the grout as instructed by the manufacturer.

• Use a rubber gloat to apply the grout.

• Remove the excess grout from the tile surfaces

• Wipe the tiles and joints gently using a grout sponge and clean water.

How To Tile An Uneven Wall

Do you know it’s almost impossible to find a wall in any home that’s fully flat and vertical? Just like floors, walls also have areas of imperfection or where they’re a bit uneven. When it comes to tiling, these are the problematic areas in which you must work around and identify how to solve to achieve a perfect finish. If not, you may as well just have the tiles sticking out and making room for moisture to creep in affecting the longevity of your project.

There a variety of options to tackle an uneven wall surface and one of the best is plastering. To make sure the surface of your wall is even, a great step would be to plaster it. Plastering of a wall can be a very simple task, however, if you lack proper training or experience, you might want to consider getting a skilled professional to handle the project for you. Making sure the surface of your wall is even is a crucial step in the tile installation process and can be quite tricky on your first trial.

Uneven wall is usually as a result of two major factors - sagging of the wall over time and the wall’s surface is not completely flat. To solve this, you’d have to detach the boards. Then, attach a new board and re-skim the walls to create a new flat and even surface you can work on. For small imperfections and dips, simply use an adhesive cement to fill in the gaps in the plaster. This approach is perfect for holes and ding with a depth that’s not more than half a centimetre. When the cement is totally dry, you can sand it to achieve a flat finish. Happy Tiling!

How To Take Tiles Off A Wall

The bonding agent or adhesive usually incorporated to hold a tile against the wall are always very strong or else you’ll find your tiles peeling off. As a result, to have them removed is not the easiest of tasks and bashing them with a hammer, will only have them broken leaving you with the task of having to scrape off the pieces. A better and much easier approach to removing tiles from a wall will be to pry them off one after the other. So how do you go about this? Let’s have a look!

lSafety First, Then Remove The First Tile

• Wear a protective eye goggle and gloves.

• Break up the grout around a tile located atthe wall’s centre using a putty knife and hammer.

• Place the putty knife under the the tile and gently it with the hammer.

lRemove The Remaining Tiles

• By tapping and prying using the tools - hammer and putty knife, wipe off all the tiles in the vertical row.

• Once done, continue to detaching the tiles in the adjacent rows until you’re able to open a wallboard section that’s around 12 inches wide and does not obstruct a stud.

• Use a keyhole blade to poke it through the wallboard.

• With the help of a reciprocating saw, cut out the wallboard’s section.

lCut The Fasteners

• Using a metal-cutting blade, cut te wallboard-holding fasteners. Make sure the fasteners holding the wallboard to the top and bottom plates of the wall are both detached.

lRemove All Wallboard Sections

• Using a similar approach, gently remove the other sections of the wallboard.

• Once completed, you can easily sweep the tiles’ broken pieces.

• Finally, vaccum the grout dust to ensure the work is neatly done.

If you lack a proper training or experience, taking off your tiles from a wall is best left to a skilled professional for the best results and to prevent potential damages which can lead to additional costs.

How To Tile A Wall

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

lHang a batten board

• Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

• Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

lForm A Pyramid Shape With The Tiles

• If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

lExamine The Floor For Level & Walls For Plumb

• If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

lThe Least Size Of Tiles To Be Used Is Half-Wide

• Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.